mayhem-firmware/firmware/chibios/os/hal/platforms/LPC11Uxx/pal_lld.h

/*
    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio

    Licensed under the Apache License, Version 2.0 (the "License");
    you may not use this file except in compliance with the License.
    You may obtain a copy of the License at

        http://www.apache.org/licenses/LICENSE-2.0

    Unless required by applicable law or agreed to in writing, software
    distributed under the License is distributed on an "AS IS" BASIS,
    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
    See the License for the specific language governing permissions and
    limitations under the License.
*/

/**
 * @file    LPC11Uxx/pal_lld.h
 * @brief   LPC11Uxx GPIO low level driver header.
 *
 * @addtogroup PAL
 * @{
 */

#ifndef _PAL_LLD_H_
#define _PAL_LLD_H_

#if HAL_USE_PAL || defined(__DOXYGEN__)

/*===========================================================================*/
/* Unsupported modes and specific modes                                      */
/*===========================================================================*/

#undef PAL_MODE_INPUT_PULLUP
#undef PAL_MODE_INPUT_PULLDOWN
#undef PAL_MODE_INPUT_ANALOG
#undef PAL_MODE_OUTPUT_OPENDRAIN

/*===========================================================================*/
/* I/O Ports Types and constants.                                            */
/*===========================================================================*/

/**
 * @brief   GPIO port setup info.
 */
typedef struct {
  /** Initial value for FIO_PIN register.*/
  uint32_t      data;
  /** Initial value for FIO_DIR register.*/
  uint32_t      dir;
} gpio_setup_t;

/**
 * @brief   GPIO static initializer.
 * @details An instance of this structure must be passed to @p palInit() at
 *          system startup time in order to initialized the digital I/O
 *          subsystem. This represents only the initial setup, specific pads
 *          or whole ports can be reprogrammed at later time.
 * @note    The @p IOCON block is not configured, initially all pins have
 *          enabled pullups and are programmed as GPIO. It is responsibility
 *          of the various drivers to reprogram the pins in the proper mode.
 *          Pins that are not handled by any driver may be programmed in
 *          @p board.c.
 */
typedef struct {
  /** @brief GPIO 0 setup data.*/
  gpio_setup_t  P0;
  /** @brief GPIO 1 setup data.*/
  gpio_setup_t  P1;
} PALConfig;

/**
 * @brief   Width, in bits, of an I/O port.
 */
#define PAL_IOPORTS_WIDTH 32

/**
 * @brief   Whole port mask.
 * @brief   This macro specifies all the valid bits into a port.
 */
#define PAL_WHOLE_PORT ((ioportmask_t)0xFFFFFFFF)

/**
 * @brief   Digital I/O port sized unsigned type.
 */
typedef uint32_t ioportmask_t;

/**
 * @brief   Digital I/O modes.
 */
typedef uint32_t iomode_t;

/**
 * @brief   Port Identifier.
 */
typedef uint32_t ioportid_t;

/*===========================================================================*/
/* I/O Ports Identifiers.                                                    */
/*===========================================================================*/

/**
 * @brief   GPIO0 port identifier.
 */
#define IOPORT1         0
#define GPIO0           0

/**
 * @brief   GPIO1 port identifier.
 */
#define IOPORT2         1
#define GPIO1           1

/*===========================================================================*/
/* Implementation, some of the following macros could be implemented as      */
/* functions, if so please put them in pal_lld.c.                            */
/*===========================================================================*/

/**
 * @brief   Low level PAL subsystem initialization.
 *
 * @param[in] config    architecture-dependent ports configuration
 *
 * @notapi
 */
#define pal_lld_init(config) _pal_lld_init(config)

/**
 * @brief   Reads the physical I/O port states.
 *
 * @param[in] port      port identifier
 * @return              The port bits.
 *
 * @notapi
 */
#define pal_lld_readport(port) (LPC_GPIO->PIN[(port)])

/**
 * @brief   Reads the output latch.
 * @details The purpose of this function is to read back the latched output
 *          value.
 *
 * @param[in] port      port identifier
 * @return              The latched logical states.
 *
 * @notapi
 */
#define pal_lld_readlatch(port) (LPC_GPIO->SET[(port)])

/**
 * @brief   Writes a bits mask on a I/O port.
 *
 * @param[in] port      port identifier
 * @param[in] bits      bits to be written on the specified port
 *
 * @notapi
 */
#define pal_lld_writeport(port, bits) (LPC_GPIO->PIN[(port)] = (bits))

/**
 * @brief   Sets a bits mask on a I/O port.
 * @note    The @ref PAL provides a default software implementation of this
 *          functionality, implement this function if can optimize it by using
 *          special hardware functionalities or special coding.
 *
 * @param[in] port      port identifier
 * @param[in] bits      bits to be ORed on the specified port
 *
 * @notapi
 */
#define pal_lld_setport(port, bits) (LPC_GPIO->SET[(port)] = (bits))

/**
 * @brief   Clears a bits mask on a I/O port.
 * @note    The @ref PAL provides a default software implementation of this
 *          functionality, implement this function if can optimize it by using
 *          special hardware functionalities or special coding.
 *
 * @param[in] port      port identifier
 * @param[in] bits      bits to be cleared on the specified port
 *
 * @notapi
 */
#define pal_lld_clearport(port, bits) (LPC_GPIO->CLR[(port)] = (bits))

/**
 * @brief   Toggles a bits mask on a I/O port.
 * @note    The @ref PAL provides a default software implementation of this
 *          functionality, implement this function if can optimize it by using
 *          special hardware functionalities or special coding.
 *
 * @param[in] port      port identifier
 * @param[in] bits      bits to be XORed on the specified port
 *
 * @notapi
 */
#define pal_lld_toggleport(port, bits) (LPC_GPIO->NOT[(port)] = (bits))

/**
 * @brief   Pads group mode setup.
 * @details This function programs a pads group belonging to the same port
 *          with the specified mode.
 * @note    Programming an unknown or unsupported mode is silently ignored.
 *
 * @param[in] port      port identifier
 * @param[in] mask      group mask
 * @param[in] offset    group bit offset within the port
 * @param[in] mode      group mode
 *
 * @notapi
 */
#define pal_lld_setgroupmode(port, mask, offset, mode)                      \
  _pal_lld_setgroupmode(port, mask << offset, mode)

/**
 * @brief   Reads a logical state from an I/O pad.
 * @note    The @ref PAL provides a default software implementation of this
 *          functionality, implement this function if can optimize it by using
 *          special hardware functionalities or special coding.
 *
 * @param[in] port      port identifier
 * @param[in] pad       pad number within the port
 * @return              The logical state.
 * @retval PAL_LOW      low logical state.
 * @retval PAL_HIGH     high logical state.
 *
 * @notapi
 */
#define pal_lld_readpad(port, pad)                                          \
  (LPC_GPIO->B[((port) * 32) + (pad)])

/**
 * @brief   Writes a logical state on an output pad.
 * @note    This function is not meant to be invoked directly by the
 *          application  code.
 * @note    The @ref PAL provides a default software implementation of this
 *          functionality, implement this function if can optimize it by using
 *          special hardware functionalities or special coding.
 *
 * @param[in] port      port identifier
 * @param[in] pad       pad number within the port
 * @param[in] bit       logical value, the value must be @p PAL_LOW or
 *                      @p PAL_HIGH
 *
 * @notapi
 */
#define pal_lld_writepad(port, pad, bit)                                    \
  ((LPC_GPIO->B[((port) * 32) + (pad)]) = (bit))

/**
 * @brief   Sets a pad logical state to @p PAL_HIGH.
 * @note    The @ref PAL provides a default software implementation of this
 *          functionality, implement this function if can optimize it by using
 *          special hardware functionalities or special coding.
 *
 * @param[in] port      port identifier
 * @param[in] pad       pad number within the port
 *
 * @notapi
 */
#define pal_lld_setpad(port, pad)                                           \
  (LPC_GPIO->SET[(port)] = 1 << (pad))

/**
 * @brief   Clears a pad logical state to @p PAL_LOW.
 * @note    The @ref PAL provides a default software implementation of this
 *          functionality, implement this function if can optimize it by using
 *          special hardware functionalities or special coding.
 *
 * @param[in] port      port identifier
 * @param[in] pad       pad number within the port
 *
 * @notapi
 */
#define pal_lld_clearpad(port, pad)                                         \
    (LPC_GPIO->CLR[(port)] = 1 << (pad))

/**
 * @brief   Toggles a pad logical state.
 * @note    The @ref PAL provides a default software implementation of this
 *          functionality, implement this function if can optimize it by using
 *          special hardware functionalities or special coding.
 *
 * @param[in] port      port identifier
 * @param[in] pad       pad number within the port
 *
 * @notapi
 */
#define pal_lld_togglepad(port, pad)                                        \
    (LPC_GPIO->NOT[(port)] = 1 << (pad))

#if !defined(__DOXYGEN__)
extern const PALConfig pal_default_config;
#endif

#ifdef __cplusplus
extern "C" {
#endif
  void _pal_lld_init(const PALConfig *config);
  void _pal_lld_setgroupmode(ioportid_t port,
                             ioportmask_t mask,
                             iomode_t mode);
#ifdef __cplusplus
}
#endif

#endif /* HAL_USE_PAL */

#endif /* _PAL_LLD_H_ */

/** @} */