mirror of
https://github.com/portapack-mayhem/mayhem-firmware.git
synced 2024-12-15 20:50:28 +00:00
65 lines
2.2 KiB
Plaintext
65 lines
2.2 KiB
Plaintext
|
/*
|
||
|
|
* Licensed under ST Liberty SW License Agreement V2, (the "License");
|
||
|
|
* You may not use this file except in compliance with the License.
|
||
|
|
* You may obtain a copy of the License at:
|
||
|
|
*
|
||
|
|
* http://www.st.com/software_license_agreement_liberty_v2
|
||
|
|
*
|
||
|
|
* Unless required by applicable law or agreed to in writing, software
|
||
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
||
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
|
|
* See the License for the specific language governing permissions and
|
||
|
|
* limitations under the License.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @defgroup SPC563 SPC563Mx Drivers
|
||
|
|
* @details This section describes all the supported drivers on the
|
||
|
|
* SPC563Mx/MPC563xM platform and the implementation details
|
||
|
|
* of the single drivers.
|
||
|
|
*
|
||
|
|
* @ingroup platforms
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @defgroup SPC563_HAL SPC563Mx Initialization Support
|
||
|
|
* @details The SPC563Mx/MPC563xM HAL support is responsible for system
|
||
|
|
* initialization.
|
||
|
|
*
|
||
|
|
* @section spc563_hal_1 Supported HW resources
|
||
|
|
* - FMPLL.
|
||
|
|
* - INTC.
|
||
|
|
* - XBAR.
|
||
|
|
* - CFLASH0.
|
||
|
|
* .
|
||
|
|
* @section spc563_hal_2 SPC563Mx HAL driver implementation features
|
||
|
|
* - FMPLL startup and stabilization.
|
||
|
|
* - Clock tree initialization.
|
||
|
|
* - Clock source selection.
|
||
|
|
* - Flash wait states initialization based on the selected clock options.
|
||
|
|
* - SYSTICK initialization based on current clock and kernel required rate.
|
||
|
|
* - DMA support initialization.
|
||
|
|
* .
|
||
|
|
* @ingroup SPC563
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @defgroup SPC563_SERIAL SPC563Mx Serial Support
|
||
|
|
* @details The SPC563Mx/MPC563xM Serial driver uses the ESCI peripherals
|
||
|
|
* in a buffered, interrupt driven, implementation.
|
||
|
|
*
|
||
|
|
* @section spc563_serial_1 Supported HW resources
|
||
|
|
* The serial driver can support any of the following hardware resources:
|
||
|
|
* - ESCIA.
|
||
|
|
* - ESCIB.
|
||
|
|
* .
|
||
|
|
* @section spc563_serial_2 SPC563Mx Serial driver implementation features
|
||
|
|
* - Clock stop for reduced power usage when the driver is in stop state.
|
||
|
|
* - Each ESCI can be independently enabled and programmed. Unused
|
||
|
|
* peripherals are left in low power mode.
|
||
|
|
* - Fully interrupt driven.
|
||
|
|
* - Programmable priority levels for each ESCI.
|
||
|
|
* .
|
||
|
|
* @ingroup SPC563
|
||
|
|
*/
|