mayhem-firmware/firmware/chibios/os/hal/platforms/Win32/pal_lld.h

/*
    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio

    Licensed under the Apache License, Version 2.0 (the "License");
    you may not use this file except in compliance with the License.
    You may obtain a copy of the License at

        http://www.apache.org/licenses/LICENSE-2.0

    Unless required by applicable law or agreed to in writing, software
    distributed under the License is distributed on an "AS IS" BASIS,
    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
    See the License for the specific language governing permissions and
    limitations under the License.
*/

/**
 * @file    Win32/pal_lld.h
 * @brief   Win32 low level simulated PAL driver header.
 *
 * @addtogroup WIN32_PAL
 * @{
 */

#ifndef _PAL_LLD_H_
#define _PAL_LLD_H_

#if HAL_USE_PAL || defined(__DOXYGEN__)

/*===========================================================================*/
/* Unsupported modes and specific modes                                      */
/*===========================================================================*/

#undef PAL_MODE_INPUT_PULLUP
#undef PAL_MODE_INPUT_PULLDOWN
#undef PAL_MODE_OUTPUT_OPENDRAIN
#undef PAL_MODE_INPUT_ANALOG

/*===========================================================================*/
/* I/O Ports Types and constants.                                            */
/*===========================================================================*/

/**
 * @brief   VIO port structure.
 */
typedef struct {
  /**
   * @brief   VIO_LATCH register.
   * @details This register represents the output latch of the VIO port.
   */
  uint32_t          latch;
  /**
   * @brief   VIO_PIN register.
   * @details This register represents the logical level at the VIO port
   *          pin level.
   */
  uint32_t          pin;
  /**
   * @brief   VIO_DIR register.
   * @details Direction of the VIO port bits, 0=input, 1=output.
   */
  uint32_t          dir;
} sim_vio_port_t;

/**
 * @brief   Virtual I/O ports static initializer.
 * @details An instance of this structure must be passed to @p palInit() at
 *          system startup time in order to initialized the digital I/O
 *          subsystem. This represents only the initial setup, specific pads
 *          or whole ports can be reprogrammed at later time.
 */
typedef struct {
  /**
   * @brief Virtual port 1 setup data.
   */
  sim_vio_port_t    VP1Data;
  /**
   * @brief Virtual port 2 setup data.
   */
  sim_vio_port_t    VP2Data;
} PALConfig;

/**
 * @brief   Width, in bits, of an I/O port.
 */
#define PAL_IOPORTS_WIDTH 32

/**
 * @brief   Whole port mask.
 * @brief   This macro specifies all the valid bits into a port.
 */
#define PAL_WHOLE_PORT ((ioportmask_t)0xFFFFFFFF)

/**
 * @brief   Digital I/O port sized unsigned type.
 */
typedef uint32_t ioportmask_t;

/**
 * @brief   Digital I/O modes.
 */
typedef uint32_t iomode_t;

/**
 * @brief   Port Identifier.
 */
typedef sim_vio_port_t *ioportid_t;

/*===========================================================================*/
/* I/O Ports Identifiers.                                                    */
/*===========================================================================*/

/**
 * @brief   VIO port 1 identifier.
 */
#define IOPORT1         (&vio_port_1)

/**
 * @brief   VIO port 2 identifier.
 */
#define IOPORT2         (&vio_port_2)

/*===========================================================================*/
/* Implementation, some of the following macros could be implemented as      */
/* functions, if so please put them in pal_lld.c.                            */
/*===========================================================================*/

/**
 * @brief   Low level PAL subsystem initialization.
 *
 * @param[in] config    architecture-dependent ports configuration
 *
 * @notapi
 */
#define pal_lld_init(config)                                                \
  (vio_port_1 = (config)->VP1Data,                                          \
   vio_port_2 = (config)->VP2Data)

/**
 * @brief   Reads the physical I/O port states.
 *
 * @param[in] port      port identifier
 * @return              The port bits.
 *
 * @notapi
 */
#define pal_lld_readport(port) ((port)->pin)

/**
 * @brief   Reads the output latch.
 * @details The purpose of this function is to read back the latched output
 *          value.
 *
 * @param[in] port      port identifier
 * @return              The latched logical states.
 *
 * @notapi
 */
#define pal_lld_readlatch(port) ((port)->latch)

/**
 * @brief   Writes a bits mask on a I/O port.
 *
 * @param[in] port      port identifier
 * @param[in] bits      bits to be written on the specified port
 *
 * @notapi
 */
#define pal_lld_writeport(port, bits) ((port)->latch = (bits))

/**
 * @brief   Pads group mode setup.
 * @details This function programs a pads group belonging to the same port
 *          with the specified mode.
 *
 * @param[in] port      port identifier
 * @param[in] mask      group mask
 * @param[in] offset    group bit offset within the port
 * @param[in] mode      group mode
 *
 * @notapi
 */
#define pal_lld_setgroupmode(port, mask, offset, mode)                      \
  _pal_lld_setgroupmode(port, mask << offset, mode)

#if !defined(__DOXYGEN__)
extern sim_vio_port_t vio_port_1;
extern sim_vio_port_t vio_port_2;
extern const PALConfig pal_default_config;
#endif

#ifdef __cplusplus
extern "C" {
#endif
  void _pal_lld_setgroupmode(ioportid_t port,
                             ioportmask_t mask,
                             iomode_t mode);
#ifdef __cplusplus
}
#endif

#endif /* HAL_USE_PAL */

#endif /* _PAL_LLD_H_ */

/** @} */