mayhem-firmware/firmware/chibios/boards/ST_STM3210C_EVAL/board.h

/*
    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio

    Licensed under the Apache License, Version 2.0 (the "License");
    you may not use this file except in compliance with the License.
    You may obtain a copy of the License at

        http://www.apache.org/licenses/LICENSE-2.0

    Unless required by applicable law or agreed to in writing, software
    distributed under the License is distributed on an "AS IS" BASIS,
    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
    See the License for the specific language governing permissions and
    limitations under the License.
*/

#ifndef _BOARD_H_
#define _BOARD_H_

/*
 * Setup for the STMicroelectronics STM3210C-EVAL evaluation board.
 */

#define GPIOD_LED1              7
#define GPIOD_LED2              13
#define GPIOD_LED3              3
#define GPIOD_LED4              4

/*
 * Board identifier.
 */
#define BOARD_ST_STM3210C_EVAL
#define BOARD_NAME              "ST STM3210C-EVAL"

/*
 * Board frequencies.
 */
#define STM32_LSECLK            32768
#define STM32_HSECLK            25000000

/*
 * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
 */
#define STM32F10X_CL

/*
 * IO pins assignments.
 * *********************TO BE COMPLETED*********************
 */

/*
 * I/O ports initial setup, this configuration is established soon after reset
 * in the initialization code.
 *
 * The digits have the following meaning:
 *   0 - Analog input.
 *   1 - Push Pull output 10MHz.
 *   2 - Push Pull output 2MHz.
 *   3 - Push Pull output 50MHz.
 *   4 - Digital input.
 *   5 - Open Drain output 10MHz.
 *   6 - Open Drain output 2MHz.
 *   7 - Open Drain output 50MHz.
 *   8 - Digital input with PullUp or PullDown resistor depending on ODR.
 *   9 - Alternate Push Pull output 10MHz.
 *   A - Alternate Push Pull output 2MHz.
 *   B - Alternate Push Pull output 50MHz.
 *   C - Reserved.
 *   D - Alternate Open Drain output 10MHz.
 *   E - Alternate Open Drain output 2MHz.
 *   F - Alternate Open Drain output 50MHz.
 * Please refer to the STM32 Reference Manual for details.
 */

/*
 * Port A setup.
 * Everything input except:
 */
#define VAL_GPIOACRL            0x44444444      /*  PA7...PA0 */
#define VAL_GPIOACRH            0x44444444      /* PA15...PA8 */
#define VAL_GPIOAODR            0xFFFFFFFF

/*
 * Port B setup.
 * Everything input except:
 */
#define VAL_GPIOBCRL            0x44444444      /*  PB7...PB0 */
#define VAL_GPIOBCRH            0x44444444      /* PB15...PB8 */
#define VAL_GPIOBODR            0xFFFFFFFF

/*
 * Port C setup.
 * Everything input except:
 */
#define VAL_GPIOCCRL            0x44444444      /*  PC7...PC0 */
#define VAL_GPIOCCRH            0x44444444      /* PC15...PC8 */
#define VAL_GPIOCODR            0xFFFFFFFF

/*
 * Port D setup.
 * Everything input except:
 * PD5 - USART2TX (remapped) AF PP Output
 * PD6 - USART2RX (remapped) Digital Input
 * PD7 - LED (LD1) PP Output
 */
#define VAL_GPIODCRL            0x34B33444      /*  PD7...PD0 */
#define VAL_GPIODCRH            0x44344444      /* PD15...PD8 */
#define VAL_GPIODODR            0x0000DF67

/*
 * Port E setup.
 * Everything input except:
 */
#define VAL_GPIOECRL            0x44444444      /*  PE7...PE0 */
#define VAL_GPIOECRH            0x44344444      /* PE15...PE8 */
#define VAL_GPIOEODR            0xFFFFFFFF

#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
  void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */

#endif /* _BOARD_H_ */