mirror of
https://github.com/portapack-mayhem/mayhem-firmware.git
synced 2024-12-24 23:17:37 +00:00
60 lines
1.8 KiB
C
60 lines
1.8 KiB
C
|
/*
|
||
|
|
SPC5 HAL - Copyright (C) 2013 STMicroelectronics
|
||
|
|
|
||
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
||
|
|
you may not use this file except in compliance with the License.
|
||
|
|
You may obtain a copy of the License at
|
||
|
|
|
||
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
||
|
|
|
||
|
|
Unless required by applicable law or agreed to in writing, software
|
||
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
||
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
|
|
See the License for the specific language governing permissions and
|
||
|
|
limitations under the License.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include "ch.h"
|
||
|
|
#include "hal.h"
|
||
|
|
|
||
|
|
#if HAL_USE_PAL || defined(__DOXYGEN__)
|
||
|
|
/* Initial setup of all defined pads, the list is terminated by a {0, 0, 0}.*/
|
||
|
|
static const spc_siu_init_t spc_siu_init[] = {
|
||
|
|
{PCR(PORT5, P5_ESCI_A_TX), PAL_HIGH, PAL_MODE_OUTPUT_ALTERNATE(1)},
|
||
|
|
{PCR(PORT5, P5_ESCI_A_RX), PAL_HIGH, PAL_MODE_OUTPUT_ALTERNATE(1)},
|
||
|
|
{PCR(PORT11, P11_BUTTON1), PAL_LOW, PAL_MODE_INPUT},
|
||
|
|
{PCR(PORT11, P11_BUTTON2), PAL_LOW, PAL_MODE_INPUT},
|
||
|
|
{PCR(PORT11, P11_BUTTON3), PAL_LOW, PAL_MODE_INPUT},
|
||
|
|
{PCR(PORT11, P11_BUTTON4), PAL_LOW, PAL_MODE_INPUT},
|
||
|
|
{PCR(PORT11, P11_LED1), PAL_HIGH, PAL_MODE_OUTPUT_PUSHPULL},
|
||
|
|
{PCR(PORT11, P11_LED2), PAL_HIGH, PAL_MODE_OUTPUT_PUSHPULL},
|
||
|
|
{PCR(PORT11, P11_LED3), PAL_HIGH, PAL_MODE_OUTPUT_PUSHPULL},
|
||
|
|
{PCR(PORT11, P11_LED4), PAL_HIGH, PAL_MODE_OUTPUT_PUSHPULL},
|
||
|
|
{0, 0, 0}
|
||
|
|
};
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief PAL setup.
|
||
|
|
*/
|
||
|
|
const PALConfig pal_default_config = {
|
||
|
|
spc_siu_init
|
||
|
|
};
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Early initialization code.
|
||
|
|
* This initialization must be performed just after stack setup and before
|
||
|
|
* any other initialization.
|
||
|
|
*/
|
||
|
|
void __early_init(void) {
|
||
|
|
|
||
|
|
spc_clock_init();
|
||
|
|
}
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Board-specific initialization code.
|
||
|
|
*/
|
||
|
|
void boardInit(void) {
|
||
|
|
|
||
|
|
}
|