mirror of
https://github.com/portapack-mayhem/mayhem-firmware.git
synced 2024-12-14 20:18:13 +00:00
270 lines
9.4 KiB
C
270 lines
9.4 KiB
C
|
/*
|
||
|
|
ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
|
||
|
|
|
||
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
||
|
|
you may not use this file except in compliance with the License.
|
||
|
|
You may obtain a copy of the License at
|
||
|
|
|
||
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
||
|
|
|
||
|
|
Unless required by applicable law or agreed to in writing, software
|
||
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
||
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
|
|
See the License for the specific language governing permissions and
|
||
|
|
limitations under the License.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @file LPC8xx/serial_lld.h
|
||
|
|
* @brief LPC8xx low level serial driver header.
|
||
|
|
*
|
||
|
|
* @addtogroup SERIAL
|
||
|
|
* @{
|
||
|
|
*/
|
||
|
|
|
||
|
|
#ifndef _SERIAL_LLD_H_
|
||
|
|
#define _SERIAL_LLD_H_
|
||
|
|
|
||
|
|
#if HAL_USE_SERIAL || defined(__DOXYGEN__)
|
||
|
|
|
||
|
|
/*===========================================================================*/
|
||
|
|
/* Driver constants. */
|
||
|
|
/*===========================================================================*/
|
||
|
|
|
||
|
|
#define CFG_ENA 0x0001
|
||
|
|
#define CFG_DL7 0x0000
|
||
|
|
#define CFG_DL8 0x0004
|
||
|
|
#define CFG_DL9 0x0008
|
||
|
|
#define CFG_NOPARITY 0x0000
|
||
|
|
#define CFG_PARITYEVEN 0x0020
|
||
|
|
#define CFG_PARITYODD 0x0030
|
||
|
|
#define CFG_STOP1 0x0000
|
||
|
|
#define CFG_STOP2 0x0040
|
||
|
|
#define CFG_CTSEN 0x0200
|
||
|
|
#define CFG_SYNCEN 0x0800
|
||
|
|
#define CFG_CLKPOL_FALL 0x0000
|
||
|
|
#define CFG_CLKPOL_RISE 0x1000
|
||
|
|
#define CFG_SYNC_SLV 0x0000
|
||
|
|
#define CFG_SYNC_MAST 0x4000
|
||
|
|
#define CFG_LOOP_EN 0x8000
|
||
|
|
|
||
|
|
#define CTRL_TXBRKEN 0x0002
|
||
|
|
#define CTRL_ADDRDET 0x0004
|
||
|
|
#define CTRL_TXDIS 0x0040
|
||
|
|
#define CTRL_CC 0x0100
|
||
|
|
#define CTRL_CLRCC 0x0200
|
||
|
|
|
||
|
|
#define STAT_RXRDY 0x0001
|
||
|
|
#define STAT_RXIDLE 0x0002
|
||
|
|
#define STAT_TXRDY 0x0004
|
||
|
|
#define STAT_TXIDLE 0x0008
|
||
|
|
#define STAT_CTS 0x0010
|
||
|
|
#define STAT_DELTACTS 0x0020
|
||
|
|
#define STAT_TXDIS 0x0040
|
||
|
|
#define STAT_OVERRUN 0x0100
|
||
|
|
#define STAT_RXBRK 0x0400
|
||
|
|
#define STAT_DELTARXBRK 0x0800
|
||
|
|
#define STAT_START 0x1000
|
||
|
|
#define STAT_FRAMERR 0x2000
|
||
|
|
#define STAT_PARITYERR 0x4000
|
||
|
|
#define STAT_RXNOISE 0x8000
|
||
|
|
|
||
|
|
|
||
|
|
/*===========================================================================*/
|
||
|
|
/* Driver pre-compile time settings. */
|
||
|
|
/*===========================================================================*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief UART0 driver enable switch.
|
||
|
|
* @details If set to @p TRUE the support for UART0 is included.
|
||
|
|
* @note The default is @p TRUE .
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_USE_UART0) || defined(__DOXYGEN__)
|
||
|
|
#define LPC8xx_SERIAL_USE_UART0 TRUE
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief UART1 driver enable switch.
|
||
|
|
* @details If set to @p TRUE the support for UART1 is included.
|
||
|
|
* @note The default is @p FALSE .
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_USE_UART1) || defined(__DOXYGEN__)
|
||
|
|
#define LPC8xx_SERIAL_USE_UART1 FALSE
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief UART2 driver enable switch.
|
||
|
|
* @details If set to @p TRUE the support for UART2 is included.
|
||
|
|
* @note The default is @p FALSE .
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_USE_UART2) || defined(__DOXYGEN__)
|
||
|
|
#define LPC8xx_SERIAL_USE_UART2 FALSE
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief UART0 interrupt priority level setting.
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_UART0_IRQ_PRIORITY) || defined(__DOXYGEN__)
|
||
|
|
#define LPC8xx_SERIAL_UART0_IRQ_PRIORITY 3
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief UART1 interrupt priority level setting.
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_UART1_IRQ_PRIORITY) || defined(__DOXYGEN__)
|
||
|
|
#define LPC8xx_SERIAL_UART1_IRQ_PRIORITY 3
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief UART2 interrupt priority level setting.
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_UART2_IRQ_PRIORITY) || defined(__DOXYGEN__)
|
||
|
|
#define LPC8xx_SERIAL_UART2_IRQ_PRIORITY 3
|
||
|
|
#endif
|
||
|
|
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief Uart Baud Clock (U_PCLK).
|
||
|
|
* @details The Baud clock rate we would like to achieve.
|
||
|
|
* @note The default is @p 11.0592MHz.
|
||
|
|
* A multiple of 1.8432MHz will give accurate
|
||
|
|
* results at all standard baud rates .
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_U_PCLK) || defined(__DOXYGEN__)
|
||
|
|
#define LPC8xx_SERIAL_U_PCLK 11059200
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief UARTCLKDIV divider.
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_UARTCLKDIV) || defined(__DOXYGEN__)
|
||
|
|
#define LPC8xx_SERIAL_UARTCLKDIV (LPC8xx_MAINCLK/LPC8xx_SERIAL_U_PCLK)
|
||
|
|
#endif
|
||
|
|
|
||
|
|
// Output from uart clock divider
|
||
|
|
#define LPC8xx_UARTDIVCLK (LPC8xx_MAINCLK/LPC8xx_SERIAL_UARTCLKDIV)
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief UARTFRGDIV
|
||
|
|
* @details Fractional Baud rate generator denominator.
|
||
|
|
* @note If used, *must* be set to 256, otherwise set to 0
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_UARTFRGDIV) || defined(__DOXYGEN__)
|
||
|
|
#if (LPC8xx_SERIAL_UARTCLKDIV != LPC8xx_SERIAL_U_PCLK)
|
||
|
|
#define LPC8xx_SERIAL_UARTFRGDIV 0xFF
|
||
|
|
#else
|
||
|
|
#define LPC8xx_SERIAL_UARTFRGDIV 0x00
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief UARTFRGMUL
|
||
|
|
* @details Fractional Baud rate generator numerator.
|
||
|
|
* Refer to LPC8xx User Manual 4.6.19 for calculation
|
||
|
|
* @note the *2, +1 and /2 are included to round to the nearest integer.
|
||
|
|
*/
|
||
|
|
#if !defined(LPC8xx_SERIAL_UARTFRGMUL) || defined(__DOXYGEN__)
|
||
|
|
#if (LPC8xx_SERIAL_UARTCLKDIV != LPC8xx_SERIAL_U_PCLK)
|
||
|
|
#define LPC8xx_SERIAL_UARTFRGMULT ( ( ( ( (LPC8xx_UARTDIVCLK- \
|
||
|
|
LPC8xx_SERIAL_U_PCLK) \
|
||
|
|
*256*2 ) \
|
||
|
|
/LPC8xx_SERIAL_U_PCLK ) \
|
||
|
|
+1 ) \
|
||
|
|
/2 )
|
||
|
|
|
||
|
|
#else
|
||
|
|
#define LPC8xx_SERIAL_UARTFRGMULT 0x00
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*===========================================================================*/
|
||
|
|
/* Derived constants and error checks. */
|
||
|
|
/*===========================================================================*/
|
||
|
|
|
||
|
|
#if (LPC8xx_SERIAL_UARTCLKDIV < 1) || (LPC8xx_SERIAL_UARTCLKDIV > 255)
|
||
|
|
#error "invalid LPC8xx_SERIAL_UARTCLKDIV setting"
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#if (LPC8xx_SERIAL_UARTFRGDIV != 0) && (LPC8xx_SERIAL_UARTFRGDIV != 255)
|
||
|
|
#error "invalid LPC8xx_SERIAL_UARTFRGDIV setting"
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#if (LPC8xx_SERIAL_UARTFRGMUL != 0) && (LPC8xx_SERIAL_UARTFRGMUL > 255)
|
||
|
|
#error "invalid LPC8xx_SERIAL_UARTFRGMUL setting"
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*===========================================================================*/
|
||
|
|
/* Driver data structures and types. */
|
||
|
|
/*===========================================================================*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief LPC8xx Serial Driver configuration structure.
|
||
|
|
* @details An instance of this structure must be passed to @p sdStart()
|
||
|
|
* in order to configure and start a serial driver operations.
|
||
|
|
*/
|
||
|
|
typedef struct {
|
||
|
|
/**
|
||
|
|
* @brief Bit rate.
|
||
|
|
*/
|
||
|
|
uint32_t sc_speed;
|
||
|
|
/**
|
||
|
|
* @brief Initialization value for the CFG register.
|
||
|
|
*/
|
||
|
|
uint32_t sc_cfg;
|
||
|
|
} SerialConfig;
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @brief @p SerialDriver specific data.
|
||
|
|
*/
|
||
|
|
#define _serial_driver_data \
|
||
|
|
_base_asynchronous_channel_data \
|
||
|
|
/* Driver state.*/ \
|
||
|
|
sdstate_t state; \
|
||
|
|
/* Input queue.*/ \
|
||
|
|
InputQueue iqueue; \
|
||
|
|
/* Output queue.*/ \
|
||
|
|
OutputQueue oqueue; \
|
||
|
|
/* Input circular buffer.*/ \
|
||
|
|
uint8_t ib[SERIAL_BUFFERS_SIZE]; \
|
||
|
|
/* Output circular buffer.*/ \
|
||
|
|
uint8_t ob[SERIAL_BUFFERS_SIZE]; \
|
||
|
|
/* End of the mandatory fields.*/ \
|
||
|
|
/* Pointer to the USART registers block.*/ \
|
||
|
|
LPC_USART_TypeDef *uart;
|
||
|
|
|
||
|
|
/*===========================================================================*/
|
||
|
|
/* Driver macros. */
|
||
|
|
/*===========================================================================*/
|
||
|
|
|
||
|
|
/*===========================================================================*/
|
||
|
|
/* External declarations. */
|
||
|
|
/*===========================================================================*/
|
||
|
|
|
||
|
|
#if LPC8xx_SERIAL_USE_UART0 && !defined(__DOXYGEN__)
|
||
|
|
extern SerialDriver SD1;
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#if LPC8xx_SERIAL_USE_UART1 && !defined(__DOXYGEN__)
|
||
|
|
extern SerialDriver SD2;
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#if LPC8xx_SERIAL_USE_UART2 && !defined(__DOXYGEN__)
|
||
|
|
extern SerialDriver SD3;
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifdef __cplusplus
|
||
|
|
extern "C" {
|
||
|
|
#endif
|
||
|
|
void sd_lld_init(void);
|
||
|
|
void sd_lld_start(SerialDriver *sdp, const SerialConfig *config);
|
||
|
|
void sd_lld_stop(SerialDriver *sdp);
|
||
|
|
#ifdef __cplusplus
|
||
|
|
}
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#endif /* HAL_USE_SERIAL */
|
||
|
|
|
||
|
|
#endif /* _SERIAL_LLD_H_ */
|
||
|
|
|
||
|
|
/** @} */
|