ChibiOS 2.6.8, until I can figure out where to get it from git.

firmware/chibios/boards/EA_LPCXPRESSO_BB_1114/board.h

@@ -0,0 +1,96 @@
+/*
+    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Setup for Embedded Artists LPCXpresso Base Board with LPC1114 daughter
+ * board.
+ */
+
+/*
+ * Board identifiers.
+ */
+#define BOARD_EA_BB_LPC1114
+#define BOARD_NAME "Embedded Artists LPCXpresso Base Board + LPC1114"
+
+/*
+ * Board frequencies.
+ */
+#define SYSOSCCLK               12000000
+
+/*
+ * SCK0 connection on this board.
+ */
+#define LPC11xx_SPI_SCK0_SELECTOR SCK0_IS_PIO2_11
+
+/*
+ * GPIO 0 initial setup.
+ */
+#define VAL_GPIO0DIR            PAL_PORT_BIT(GPIO0_OLEDSEL) |               \
+                                PAL_PORT_BIT(GPIO0_LED2)
+#define VAL_GPIO0DATA           PAL_PORT_BIT(GPIO0_OLEDSEL) |               \
+                                PAL_PORT_BIT(GPIO0_LED2)
+
+/*
+ * GPIO 1 initial setup.
+ */
+#define VAL_GPIO1DIR            PAL_PORT_BIT(GPIO1_LED3B)   |               \
+                                PAL_PORT_BIT(GPIO1_LED3R)   |               \
+                                PAL_PORT_BIT(GPIO1_LED3G)   |               \
+                                PAL_PORT_BIT(GPIO1_SPI0SEL)
+#define VAL_GPIO1DATA           PAL_PORT_BIT(GPIO1_LED3B)   |               \
+                                PAL_PORT_BIT(GPIO1_LED3R)   |               \
+                                PAL_PORT_BIT(GPIO1_LED3G)   |               \
+                                PAL_PORT_BIT(GPIO1_SPI0SEL)
+
+/*
+ * GPIO 2 initial setup.
+ */
+#define VAL_GPIO2DIR            0x00000000
+#define VAL_GPIO2DATA           0x00000000
+
+/*
+ * GPIO 3 initial setup.
+ */
+#define VAL_GPIO3DIR            0x00000000
+#define VAL_GPIO3DATA           0x00000000
+
+/*
+ * Pin definitions.
+ */
+#define GPIO0_SW3               1
+#define GPIO0_OLEDSEL           2
+#define GPIO0_LED2              7
+
+#define GPIO1_LED3B             2
+#define GPIO1_SW4               4
+#define GPIO1_LED3R             9
+#define GPIO1_LED3G             10
+#define GPIO1_SPI0SEL           11
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+  void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+#endif /* _BOARD_H_ */