ChibiOS 2.6.8, until I can figure out where to get it from git.

firmware/chibios/boards/EA_LPCXPRESSO_LPC812/board.h

@@ -0,0 +1,125 @@
+/*
+    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Setup for Embedded Artists LPCXpresso LPC812 board.
+ */
+
+/*
+ * Board identifiers.
+ */
+#define BOARD_EA_LPC812
+#define BOARD_NAME "Embedded Artists LPCXpresso LPC812"
+
+/*
+ * Board frequencies.
+ */
+#define SYSOSCCLK               12000000
+
+
+/*
+ * I/O ports initial setup, this configuration is established soon after reset
+ * in the initialization code.
+ * Please refer to the LPC8xx Reference Manual for details.
+ */
+/* Pull-up/down  */
+#define PIN_MODE_NOPULL               (0<<3)
+#define PIN_MODE_PULLDOWN             (1<<3)
+#define PIN_MODE_PULLUP               (2<<3)
+#define PIN_MODE_REPEATER             (3<<3)
+/* Hysteresis */
+#define PIN_HYS_EN                    (1<<5)
+/* Invert Input */
+#define PIN_INV_INPUT                 (1<<6)
+/* Reserved bits */
+#define PIN_RSVD                      (1<<7)
+/* I2C Mode */
+#define PIN_I2CMODE_STD               (0<<8)
+#define PIN_I2CMODE_STDIO             (1<<8)
+#define PIN_I2CMODE_FAST              (2<<8)
+/* Open Drain */
+#define PIN_OPEN_DRAIN                (1<<10)
+/* Input Filter Sample Clocks */
+#define PIN_SMODE_FILTER(n)           ((n)<<11)
+/* Input Filter clock divider */
+#define PIN_CLKDIV_FILTER(n)          ((n)<<13)
+
+/*
+ * Pin definitions.
+ */
+#define LED_RED                        7
+#define LED_BLUE                      16
+#define LED_GREEN                     17
+
+
+/*
+ * GPIO 0 initial setup.
+ */
+/*#define VAL_PIO0_0              PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_1              PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_2              PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_3              PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_4              PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_5              PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_6              PIN_MODE_PULLUP*/
+#define VAL_PIO0_7              PIN_MODE_NOPULL
+/*#define VAL_PIO0_8              PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_9              PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_10             PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_11             PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_12             PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_13             PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_14             PIN_MODE_PULLUP*/
+/*#define VAL_PIO0_15             PIN_MODE_PULLUP*/
+#define VAL_PIO0_16             PIN_MODE_NOPULL
+#define VAL_PIO0_17             PIN_MODE_NOPULL
+
+    /* UART0: TXD = P0.4, RXD  = P0.0)*/
+#define VAL_PINASSIGN0            ((0xFFFF0000) | (0<<8) | (4))
+/*#define VAL_PINASSIGN1            0xFFFFFFFF*/
+/*#define VAL_PINASSIGN2            0xFFFFFFFF*/
+/*#define VAL_PINASSIGN3            0xFFFFFFFF*/
+/*#define VAL_PINASSIGN4            0xFFFFFFFF*/
+/*#define VAL_PINASSIGN5            0xFFFFFFFF*/
+/*#define VAL_PINASSIGN6            0xFFFFFFFF*/
+/*#define VAL_PINASSIGN7            0xFFFFFFFF*/
+/*#define VAL_PINASSIGN8            0xFFFFFFFF*/
+
+
+#define VAL_GPIO0DIR            (PAL_PORT_BIT(LED_RED)   |           \
+                                 PAL_PORT_BIT(LED_BLUE)   |          \
+                                 PAL_PORT_BIT(LED_GREEN))
+                                
+#define VAL_GPIO0DATA           (PAL_PORT_BIT(LED_RED)   |           \
+                                 PAL_PORT_BIT(LED_BLUE)   |          \
+                                 PAL_PORT_BIT(LED_GREEN))
+
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+  void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+
+#endif /* _BOARD_H_ */