mirror of
https://github.com/portapack-mayhem/mayhem-firmware.git
synced 2024-12-14 12:08:40 +00:00
126 lines
4.1 KiB
C
Executable File
126 lines
4.1 KiB
C
Executable File
/*
|
|
ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
|
|
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
|
you may not use this file except in compliance with the License.
|
|
You may obtain a copy of the License at
|
|
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
Unless required by applicable law or agreed to in writing, software
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
See the License for the specific language governing permissions and
|
|
limitations under the License.
|
|
*/
|
|
|
|
#ifndef _BOARD_H_
|
|
#define _BOARD_H_
|
|
|
|
/*
|
|
* Setup for Embedded Artists LPCXpresso LPC812 board.
|
|
*/
|
|
|
|
/*
|
|
* Board identifiers.
|
|
*/
|
|
#define BOARD_EA_LPC812
|
|
#define BOARD_NAME "Embedded Artists LPCXpresso LPC812"
|
|
|
|
/*
|
|
* Board frequencies.
|
|
*/
|
|
#define SYSOSCCLK 12000000
|
|
|
|
|
|
/*
|
|
* I/O ports initial setup, this configuration is established soon after reset
|
|
* in the initialization code.
|
|
* Please refer to the LPC8xx Reference Manual for details.
|
|
*/
|
|
/* Pull-up/down */
|
|
#define PIN_MODE_NOPULL (0<<3)
|
|
#define PIN_MODE_PULLDOWN (1<<3)
|
|
#define PIN_MODE_PULLUP (2<<3)
|
|
#define PIN_MODE_REPEATER (3<<3)
|
|
/* Hysteresis */
|
|
#define PIN_HYS_EN (1<<5)
|
|
/* Invert Input */
|
|
#define PIN_INV_INPUT (1<<6)
|
|
/* Reserved bits */
|
|
#define PIN_RSVD (1<<7)
|
|
/* I2C Mode */
|
|
#define PIN_I2CMODE_STD (0<<8)
|
|
#define PIN_I2CMODE_STDIO (1<<8)
|
|
#define PIN_I2CMODE_FAST (2<<8)
|
|
/* Open Drain */
|
|
#define PIN_OPEN_DRAIN (1<<10)
|
|
/* Input Filter Sample Clocks */
|
|
#define PIN_SMODE_FILTER(n) ((n)<<11)
|
|
/* Input Filter clock divider */
|
|
#define PIN_CLKDIV_FILTER(n) ((n)<<13)
|
|
|
|
/*
|
|
* Pin definitions.
|
|
*/
|
|
#define LED_RED 7
|
|
#define LED_BLUE 16
|
|
#define LED_GREEN 17
|
|
|
|
|
|
/*
|
|
* GPIO 0 initial setup.
|
|
*/
|
|
/*#define VAL_PIO0_0 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_1 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_2 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_3 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_4 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_5 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_6 PIN_MODE_PULLUP*/
|
|
#define VAL_PIO0_7 PIN_MODE_NOPULL
|
|
/*#define VAL_PIO0_8 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_9 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_10 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_11 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_12 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_13 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_14 PIN_MODE_PULLUP*/
|
|
/*#define VAL_PIO0_15 PIN_MODE_PULLUP*/
|
|
#define VAL_PIO0_16 PIN_MODE_NOPULL
|
|
#define VAL_PIO0_17 PIN_MODE_NOPULL
|
|
|
|
/* UART0: TXD = P0.4, RXD = P0.0)*/
|
|
#define VAL_PINASSIGN0 ((0xFFFF0000) | (0<<8) | (4))
|
|
/*#define VAL_PINASSIGN1 0xFFFFFFFF*/
|
|
/*#define VAL_PINASSIGN2 0xFFFFFFFF*/
|
|
/*#define VAL_PINASSIGN3 0xFFFFFFFF*/
|
|
/*#define VAL_PINASSIGN4 0xFFFFFFFF*/
|
|
/*#define VAL_PINASSIGN5 0xFFFFFFFF*/
|
|
/*#define VAL_PINASSIGN6 0xFFFFFFFF*/
|
|
/*#define VAL_PINASSIGN7 0xFFFFFFFF*/
|
|
/*#define VAL_PINASSIGN8 0xFFFFFFFF*/
|
|
|
|
|
|
#define VAL_GPIO0DIR (PAL_PORT_BIT(LED_RED) | \
|
|
PAL_PORT_BIT(LED_BLUE) | \
|
|
PAL_PORT_BIT(LED_GREEN))
|
|
|
|
#define VAL_GPIO0DATA (PAL_PORT_BIT(LED_RED) | \
|
|
PAL_PORT_BIT(LED_BLUE) | \
|
|
PAL_PORT_BIT(LED_GREEN))
|
|
|
|
|
|
#if !defined(_FROM_ASM_)
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
void boardInit(void);
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
#endif /* _FROM_ASM_ */
|
|
|
|
|
|
#endif /* _BOARD_H_ */
|