mirror of
https://github.com/portapack-mayhem/mayhem-firmware.git
synced 2024-12-15 04:28:10 +00:00
105 lines
3.3 KiB
Plaintext
Executable File
105 lines
3.3 KiB
Plaintext
Executable File
/*
|
|
ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
|
|
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
|
you may not use this file except in compliance with the License.
|
|
You may obtain a copy of the License at
|
|
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
Unless required by applicable law or agreed to in writing, software
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
See the License for the specific language governing permissions and
|
|
limitations under the License.
|
|
*/
|
|
|
|
/**
|
|
* @defgroup LPC8xx LPC8xx Drivers
|
|
* @details This section describes all the supported drivers on the LPC8xx
|
|
* platform and the implementation details of the single drivers.
|
|
*
|
|
* @ingroup platforms
|
|
*/
|
|
|
|
/**
|
|
* @defgroup LPC8xx_HAL LPC8xx Initialization Support
|
|
* @details The LPC8xx HAL support is responsible for system initialization.
|
|
*
|
|
* @section lpc8xx_hal_1 Supported HW resources
|
|
* - SYSCON.
|
|
* - Flash.
|
|
* .
|
|
* @section lpc8xx_hal_2 LPC8xx HAL driver implementation features
|
|
* - Clock tree initialization.
|
|
* - Clock source selection.
|
|
* - Flash controller initialization.
|
|
* - SYSTICK initialization based on current clock and kernel required rate.
|
|
* .
|
|
* @ingroup LPC8xx
|
|
*/
|
|
|
|
/**
|
|
* @defgroup LPC8xx_GPT LPC8xx GPT Support
|
|
* @details The LPC8xx GPT driver uses the MRT peripheral.
|
|
*
|
|
* @section lpc8xx_gpt_1 Supported HW resources
|
|
* - MRT.
|
|
* .
|
|
* @section lpc8xx_gpt_2 LPC8xx GPT driver implementation features
|
|
* - Each timer can be independently enabled and programmed.
|
|
* - Programmable MRT interrupt priority level.
|
|
* .
|
|
* @ingroup LPC8xx
|
|
*/
|
|
|
|
/**
|
|
* @defgroup LPC8xx_PAL LPC8xx PAL Support
|
|
* @details The LPC8xx PAL driver uses the GPIO peripheral.
|
|
*
|
|
* @section lpc8xx_pal_1 Supported HW resources
|
|
* - GPIO_PORT.
|
|
* .
|
|
* @section lpc8xx_pal_2 LPC8xx PAL driver implementation features
|
|
* - 18 bits wide ports.
|
|
* - Atomic set/reset functions.
|
|
* - Atomic Toggle functions.
|
|
* - Atomic set+reset function (atomic bus operations).
|
|
* - Output latched regardless of the pad setting.
|
|
* - Direct read of input pads regardless of the pad setting.
|
|
* .
|
|
* @section lpc8xx_pal_3 Supported PAL setup modes
|
|
* - @p PAL_MODE_RESET.
|
|
* - @p PAL_MODE_UNCONNECTED.
|
|
* - @p PAL_MODE_INPUT.
|
|
* - @p PAL_MODE_OUTPUT_PUSHPULL.
|
|
* .
|
|
* Any attempt to setup an invalid mode is ignored.
|
|
*
|
|
* @section lpc8xx_pal_4 Suboptimal behavior
|
|
* Some GPIO features are less than optimal:
|
|
* - Group operations are not atomic.
|
|
* - Pull-up and Pull-down resistors cannot be programmed through the PAL
|
|
* driver and must be programmed separately using the IOCON peripheral.
|
|
* .
|
|
* @ingroup LPC8xx
|
|
*/
|
|
|
|
/**
|
|
* @defgroup LPC8xx_SERIAL LPC8xx Serial Support
|
|
* @details The LPC8xx Serial driver uses the UART peripheral in a
|
|
* buffered, interrupt driven, implementation.
|
|
*
|
|
* @section lpc8xx_serial_1 Supported HW resources
|
|
* The serial driver can support any of the following hardware resources:
|
|
* - UART.
|
|
* .
|
|
* @section lpc8xx_serial_2 LPC8xx Serial driver implementation features
|
|
* - Clock stop for reduced power usage when the driver is in stop state.
|
|
* - Fully interrupt driven.
|
|
* - Programmable priority level.
|
|
* .
|
|
* @ingroup LPC8xx
|
|
*/
|
|
|