mirror of
https://github.com/portapack-mayhem/mayhem-firmware.git
synced 2024-12-14 20:18:13 +00:00
194 lines
6.3 KiB
C
Executable File
194 lines
6.3 KiB
C
Executable File
/*
|
|
ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
|
|
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
|
you may not use this file except in compliance with the License.
|
|
You may obtain a copy of the License at
|
|
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
Unless required by applicable law or agreed to in writing, software
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
See the License for the specific language governing permissions and
|
|
limitations under the License.
|
|
*/
|
|
|
|
#ifndef _BOARD_H_
|
|
#define _BOARD_H_
|
|
|
|
/*
|
|
* Setup for the Olimex STM32-P107 Rev.A evaluation board.
|
|
*/
|
|
|
|
/*
|
|
* Board identifier.
|
|
*/
|
|
#define BOARD_OLIMEX_STM32_P107_REV_A
|
|
#define BOARD_NAME "Olimex STM32-P107 Rev.A"
|
|
|
|
/*
|
|
* Board frequencies.
|
|
*/
|
|
#define STM32_LSECLK 32768
|
|
#define STM32_HSECLK 25000000
|
|
|
|
/*
|
|
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
|
|
*/
|
|
#define STM32F10X_CL
|
|
|
|
/*
|
|
* Ethernet PHY type.
|
|
*/
|
|
#define BOARD_PHY_ID MII_STE101P_ID
|
|
#define BOARD_PHY_RMII
|
|
|
|
/*
|
|
* IO pins assignments.
|
|
*/
|
|
#define GPIOA_SWITCH_WKUP 0
|
|
#define GPIOA_SPI3_CS_MMC 4
|
|
#define GPIOC_LED_STATUS1 6
|
|
#define GPIOC_LED_STATUS2 7
|
|
#define GPIOC_SWITCH_TAMPER 13
|
|
|
|
/*
|
|
* I/O ports initial setup, this configuration is established soon after reset
|
|
* in the initialization code.
|
|
*
|
|
* The digits have the following meaning:
|
|
* 0 - Analog input.
|
|
* 1 - Push Pull output 10MHz.
|
|
* 2 - Push Pull output 2MHz.
|
|
* 3 - Push Pull output 50MHz.
|
|
* 4 - Digital input.
|
|
* 5 - Open Drain output 10MHz.
|
|
* 6 - Open Drain output 2MHz.
|
|
* 7 - Open Drain output 50MHz.
|
|
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
|
|
* 9 - Alternate Push Pull output 10MHz.
|
|
* A - Alternate Push Pull output 2MHz.
|
|
* B - Alternate Push Pull output 50MHz.
|
|
* C - Reserved.
|
|
* D - Alternate Open Drain output 10MHz.
|
|
* E - Alternate Open Drain output 2MHz.
|
|
* F - Alternate Open Drain output 50MHz.
|
|
* Please refer to the STM32 Reference Manual for details.
|
|
*/
|
|
|
|
/*
|
|
* Port A setup.
|
|
* Everything input with pull-up except:
|
|
* PA0 - Normal input (WKUP BUTTON).
|
|
* PA1 - Normal input (ETH_RMII_REF_CLK).
|
|
* PA2 - Alternate output (ETH_RMII_MDIO).
|
|
* PA3 - Input with PU (unconnected).
|
|
* PA4 - Open Drain output (CS_MMC).
|
|
* PA5 - Input with PU (unconnected).
|
|
* PA6 - Input with PU (unconnected).
|
|
* PA7 - Normal input (ETH_RMII_CRS_DV).
|
|
* PA8 - Alternate output (MCO).
|
|
* PA9 - Normal input (OTG_VBUS).
|
|
* PA10 - Normal input (OTG_ID).
|
|
* PA11 - Normal input (OTG_DM).
|
|
* PA12 - Normal input (OTG_DP).
|
|
* PA13 - Normal input (TMS).
|
|
* PA14 - Normal input (TCK).
|
|
* PA15 - Normal input (TDI).
|
|
*/
|
|
#define VAL_GPIOACRL 0x48878B44 /* PA7...PA0 */
|
|
#define VAL_GPIOACRH 0x4444444B /* PA15...PA8 */
|
|
#define VAL_GPIOAODR 0xFFFFFFFF
|
|
|
|
/*
|
|
* Port B setup:
|
|
* PB0 - Input with PU (unconnected).
|
|
* PB1 - Input with PU (unconnected).
|
|
* PB2 - Normal input (BOOT1).
|
|
* PB3 - Normal input (TDO).
|
|
* PB4 - Normal input (TRST).
|
|
* PB5 - Input with PU (unconnected).
|
|
* PB6 - Input with PU (unconnected).
|
|
* PB7 - Input with PU (unconnected).
|
|
* PB8 - Alternate O.D. (I2C1 SCL, remapped).
|
|
* PB9 - Alternate O.D. (I2C1 SDA, remapped).
|
|
* PB10 - Input with PU (unconnected).
|
|
* PB11 - Alternate output (ETH_RMII_TX_EN).
|
|
* PB12 - Alternate output (ETH_RMII_TXD0).
|
|
* PB13 - Alternate output (ETH_RMII_TXD1).
|
|
* PB14 - Input with PU (unconnected).
|
|
* PB15 - Push Pull output (CS_UEXT).
|
|
*/
|
|
#define VAL_GPIOBCRL 0x88844488 /* PB7...PB0 */
|
|
#define VAL_GPIOBCRH 0x38BBB8FF /* PB15...PB8 */
|
|
#define VAL_GPIOBODR 0xFFFFFFFF
|
|
|
|
/*
|
|
* Port C setup:
|
|
* PC0 - Input with PU (unconnected).
|
|
* PC1 - Alternate output (ETH_MDC).
|
|
* PC2 - Input with PU (unconnected).
|
|
* PC3 - Input with PU (unconnected).
|
|
* PC4 - Normal input (ETH_RMII_RXD0).
|
|
* PC5 - Normal input (ETH_RMII_RXD1).
|
|
* PC6 - Push Pull output (STAT1 green LED).
|
|
* PC7 - Push Pull output (STAT2 yellow LED).
|
|
* PC8 - Input with PU (unconnected).
|
|
* PC9 - Input with PU (unconnected).
|
|
* PC10 - Alternate output (SPI3 SCK).
|
|
* PC11 - Input with PU (SPI3 MISO).
|
|
* PC12 - Alternate output (SPI3 MOSI).
|
|
* PC13 - Normal input (TAMPER).
|
|
* PC14 - Normal input (OSC32 IN).
|
|
* PC15 - Normal input (OSC32 OUT).
|
|
*/
|
|
#define VAL_GPIOCCRL 0x334488B8 /* PC7...PC0 */
|
|
#define VAL_GPIOCCRH 0x444B8B88 /* PC15...PC8 */
|
|
#define VAL_GPIOCODR 0xFFFFFF3F
|
|
|
|
/*
|
|
* Port D setup:
|
|
* PD0 - Input with PU (unconnected).
|
|
* PD1 - Input with PU (unconnected).
|
|
* PD2 - Input with PU (unconnected).
|
|
* PD3 - Input with PU (unconnected).
|
|
* PD4 - Input with PU (unconnected).
|
|
* PD5 - Alternate output (USART2 TX, UEXT).
|
|
* PD6 - Input with PU (USART2 RX, UEXT).
|
|
* PD7 - Push Pull output (USB_VBUSON).
|
|
* PD8 - Alternate output (USART2 TX, remapped).
|
|
* PD9 - Normal input (USART2 RX, remapped).
|
|
* PD10 - Input with PU (unconnected).
|
|
* PD11 - Normal input (USART2 CTS, remapped).
|
|
* PD12 - Alternate output (USART2 RTS, remapped).
|
|
* PD13 - Input with PU (unconnected).
|
|
* PD14 - Input with PU (unconnected).
|
|
* PD15 - Input with PU (unconnected).
|
|
*/
|
|
#define VAL_GPIODCRL 0x38B88888 /* PD7...PD0 */
|
|
#define VAL_GPIODCRH 0x888B484B /* PD15...PD8 */
|
|
#define VAL_GPIODODR 0xFFFFFFFF
|
|
|
|
/*
|
|
* Port E setup.
|
|
* Everything input with pull-up except:
|
|
* PE14 - Normal input (ETH_RMII_MDINT).
|
|
* PE15 - Normal input (USB_FAULT).
|
|
*/
|
|
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
|
|
#define VAL_GPIOECRH 0x44888888 /* PE15...PE8 */
|
|
#define VAL_GPIOEODR 0xFFFFFFFF
|
|
|
|
#if !defined(_FROM_ASM_)
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
void boardInit(void);
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
#endif /* _FROM_ASM_ */
|
|
|
|
#endif /* _BOARD_H_ */
|