mirror of
https://github.com/portapack-mayhem/mayhem-firmware.git
synced 2024-12-25 13:37:38 +00:00
94 lines
3.1 KiB
Plaintext
Executable File
94 lines
3.1 KiB
Plaintext
Executable File
/*
|
|
ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
|
|
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
|
you may not use this file except in compliance with the License.
|
|
You may obtain a copy of the License at
|
|
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
Unless required by applicable law or agreed to in writing, software
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
See the License for the specific language governing permissions and
|
|
limitations under the License.
|
|
*/
|
|
|
|
/**
|
|
* @defgroup MSP430_DRIVERS MSP430 Drivers
|
|
* @details This section describes all the supported drivers on the MSP430
|
|
* platform and the implementation details of the single drivers.
|
|
*
|
|
* @ingroup platforms
|
|
*/
|
|
|
|
/**
|
|
* @defgroup MSP430_HAL MSP430 Initialization Support
|
|
* @details The MSP430 HAL support is responsible for system initialization.
|
|
*
|
|
* @section msp430_hal_1 Supported HW resources
|
|
* - DCOCTL.
|
|
* - BCSCTL1.
|
|
* - BCSCTL2.
|
|
* .
|
|
* @section msp430_hal_2 MSP430 HAL driver implementation features
|
|
* - Clock source selection.
|
|
* .
|
|
* @ingroup MSP430_DRIVERS
|
|
*/
|
|
|
|
/**
|
|
* @defgroup MSP430_PAL MSP430 PAL Support
|
|
* @details The MSP430 PAL driver uses the PORT peripherals.
|
|
*
|
|
* @section msp430_pal_1 Supported HW resources
|
|
* - PORT1 (where present).
|
|
* - PORT2 (where present).
|
|
* - PORT3 (where present).
|
|
* - PORT4 (where present).
|
|
* - PORT5 (where present).
|
|
* - PORT6 (where present).
|
|
* .
|
|
* @section msp430_pal_2 MSP430 PAL driver implementation features
|
|
* The PAL driver implementation fully supports the following hardware
|
|
* capabilities:
|
|
* - 8 bits wide ports.
|
|
* - Atomic set/reset/toggle functions because special MSP430 instruction set.
|
|
* - Output latched regardless of the pad setting.
|
|
* - Direct read of input pads regardless of the pad setting.
|
|
* .
|
|
* @section msp430_pal_3 Supported PAL setup modes
|
|
* The MSP430 PAL driver supports the following I/O modes:
|
|
* - @p PAL_MODE_RESET.
|
|
* - @p PAL_MODE_UNCONNECTED.
|
|
* - @p PAL_MODE_INPUT.
|
|
* - @p PAL_MODE_OUTPUT_PUSHPULL.
|
|
* .
|
|
* Any attempt to setup an invalid mode is ignored.
|
|
*
|
|
* @section msp430_pal_4 Suboptimal behavior
|
|
* The MSP430 PORT is less than optimal in several areas, the limitations
|
|
* should be taken in account while using the PAL driver:
|
|
* - Bus/group writes is not atomic.
|
|
* - Pad/group mode setup is not atomic.
|
|
* .
|
|
* @ingroup MSP430_DRIVERS
|
|
*/
|
|
|
|
/**
|
|
* @defgroup MSP430_SERIAL MSP430 Serial Support
|
|
* @details The MSP430 Serial driver uses the USART peripherals in a
|
|
* buffered, interrupt driven, implementation.
|
|
*
|
|
* @section msp430_serial_1 Supported HW resources
|
|
* The serial driver can support any of the following hardware resources:
|
|
* - USART0.
|
|
* - USART1.
|
|
* .
|
|
* @section msp430_serial_2 MSP430 Serial driver implementation features
|
|
* - Each USART can be independently enabled and programmed.
|
|
* - Fully interrupt driven.
|
|
* .
|
|
* @ingroup MSP430_DRIVERS
|
|
*/
|