TheArchive/mayhem-firmware
1
0
Fork 0
mirror of https://github.com/portapack-mayhem/mayhem-firmware.git synced 2024-11-30 13:35:31 +00:00
Code Issues Packages Projects Releases Wiki Activity

Destroyed Microphone Tranceiver (markdown)

Si 2022-02-24 16:24:39 +00:00
parent 02df17229a
commit ee356a9dd2
1 changed files with 0 additions and 33 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

33
Microphone-Tranceiver.md

@ -1,33 +0,0 @@
The Microphone App provides a Narrow band FM transmitter application, that allows the transmission of voice and when not transmitting allows you to receive in a simplex way if configured.
## Key Controls
* **MIC. GAIN:** Cursor selection and use rotary encoder is used to select a fixed gain of x0.5, x1.0, x1.5, x2.0. The setting needs to be selected based, on the Microphone used which is connected via the Headset/ Microphone socket (standard smartphone 4 segment 3.5mm connector). The sensitivity of the microphone is shown on the lefthand side and should be configured so the range is green for most of the audio and never hits red to limit over deviation of the signal.
* **F:** This field set the Frequency for the transmission.
* **BW:** This field sets the Band Width of the transmission under normal conditions from 0-150 kHz.
* **GAIN:** Is set for LNA(IF) and (0-47) and AMP 0dB or 14dB.Node mode is set to FM only.
* **TX Activation:** Field can be selected for one of three settings. Off, PTT, AUTO. In the PTT setting, the PortaPack will transmit when the TX button and the bottom of the App screen is pressed on the touch screen. In AUTO the Receiver section below is not active, but the triggering is set by the following 3 settings.
* **LVL:** The level that triggers the transmission is set by the audio level going over the threshold value set (0-255). This can be seen as a grey dash marked next to the vu-meter and shows its current setting compared to the microphone level.
* **ATT:** This is the attack time of the microphone audio level must be above the set threshold to start transmitting (0 to 999mS). Higher attack helps avoid false triggers but might cut off the first words you say.
* **DEC:** This is the decay time of the microphone audio signal falls below the threshold level be for the transmission is stopped (0 to 9999mS). Lower decay avoids silence at the end of the message but might cut you off in the middle of a sentence. Adjust levels depending on your speaking habits.
* **TONE KEY:** The Tick box next to “Roger Beep” can be selected with effort with cursor or better to select with touch screen. This will add a roger bleep if enabled. Note the level of the Tone % compared to the Microphone setting is set in Options >Audio.
RX audio listening: The Tick box to select this item is difficult to select with cursor having to go down and up though item, and with some luck you may enable the box. It is better to select from the touch screen. If this is enabled then it will turn on the Audio Receiver and with the following setting will allow you to listen to a receive channel when not transmitting. The TX-RX timing gap is not known. The frequency can be set separately to that of the transmitter section above. The following setting can be applied to the receiver.
* **FM RX BW:** The is the narrow band FM Receiver Band Width setting. It can be set to either 8k5kHz,11Khz or 16kHz.
* **F:** The frequency can be set in the usual way with text pad when selected
* **SQ:** This can be set between 0 and 99 typically 50 is threshold.
* **GAIN:** The gain setting of LNA(IF) (0-40) VGA(Baseband)(0-62) and AMP 0=0db or 1=14dB.
Note this application while performing a transmit function may well over deviate and generate unwanted harmonics.