We were copying 12 out of the 16 bytes which meant that
the 1:1 NAT required would only work if the last 4 bytes
happened to match between the new and old address, something
that our tests accidentally had. Fix it by copying the full
16 bytes and make the tests also verify the addr and use rand
addresses.
Updates #9511
Signed-off-by: Maisem Ali <maisem@tailscale.com>
We now allow some more ICMP errors to flow, specifically:
- ICMP parameter problem in both IPv4 and IPv6 (corrupt headers)
- ICMP Packet Too Big (for IPv6 PMTU)
Updates #311
Updates #8102
Updates #11002
Signed-off-by: James Tucker <james@tailscale.com>
Run `staticcheck` with `U1000` to find unused code. This cleans up about
a half of it. I'll do the other half separately to keep PRs manageable.
Updates #cleanup
Signed-off-by: Andrew Lytvynov <awly@tailscale.com>
The current structure meant that we were embedding netstack in
the tailscale CLI and in the GUIs. This removes that by isolating
the checksum munging to a different pkg which is only called from
`net/tstun`.
Fixes#9756
Signed-off-by: Maisem Ali <maisem@tailscale.com>
Implements the ability for the address-rewriting code to support rewriting IPv6 addresses.
Specifically, UpdateSrcAddr & UpdateDstAddr.
Signed-off-by: Tom DNetto <tom@tailscale.com>
Updates https://github.com/tailscale/corp/issues/11202
This adds support in tstun to utitilize the SelfNodeV4MasqAddrForThisPeer and
perform the necessary modifications to the packet as it passes through tstun.
Currently this only handles ICMP, UDP and TCP traffic.
Subnet routers and Exit Nodes are also unsupported.
Updates tailscale/corp#8020
Co-authored-by: Melanie Warrick <warrick@tailscale.com>
Signed-off-by: Maisem Ali <maisem@tailscale.com>
This updates all source files to use a new standard header for copyright
and license declaration. Notably, copyright no longer includes a date,
and we now use the standard SPDX-License-Identifier header.
This commit was done almost entirely mechanically with perl, and then
some minimal manual fixes.
Updates #6865
Signed-off-by: Will Norris <will@tailscale.com>
01b90df2fa added SCTP support before
(with explicit parsing for ports) and
69de3bf7bf tried to add support for
arbitrary IP protocols (as long as the ACL permited a port of "*",
since we might not know how to find ports from an arbitrary IP
protocol, if it even has such a concept). But apparently that latter
commit wasn't tested end-to-end enough. It had a lot of tests, but the
tests made assumptions about layering that either weren't true, or
regressed since 1.20. Notably, it didn't remove the (*Filter).pre
bidirectional filter that dropped all "unknown" protocol packets both
leaving and entering, even if there were explicit protocol matches
allowing them in.
Also, don't map all unknown protocols to 0. Keep their IP protocol
number parsed so it's matchable by later layers. Only reject illegal
things.
Fixes#6423
Updates #2162
Updates #2163
Change-Id: I9659b3ece86f4db51d644f9b34df78821758842c
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The fragment offset is an 8 byte offset rather than a byte offset, so
the short packet limit is now in fragment block size in order to compare
with the offset value.
The packet flags are in the first 3 bits of the flags/frags byte, and
so after conversion to a uint16 little endian value they are at the
start, not the end of the value - the mask for extracting "more
fragments" is adjusted to match this byte.
Extremely short fragments less than 80 bytes are dropped, but fragments
over 80 bytes are now accepted.
Fixes#5727
Signed-off-by: James Tucker <james@tailscale.com>
It will be used for ICMPv6 next, so pass in the proto.
Also, use the ipproto constants rather than hardcoding the mysterious
number.
Change-Id: I57b68bdd2d39fff75f82affe955aff9245de246b
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
There are a few remaining uses of testing.AllocsPerRun:
Two in which we only log the number of allocations,
and one in which dynamically calculate the allocations
target based on a different AllocsPerRun run.
This also allows us to tighten the "no allocs"
test in wgengine/filter.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
For discovery when an explicit hostname/IP is known. We'll still
also send it via control for finding peers by a list.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Add proto to flowtrack.Tuple.
Add types/ipproto leaf package to break a cycle.
Server-side ACL work remains.
Updates #1516
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Unused for now, but I want to backport this commit to 1.4 so 1.6 can
start sending these and then at least 1.4 logs will stringify nicely.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This adds a new IP Protocol type, TSMP on protocol number 99 for
sending inter-tailscale messages over WireGuard, currently just for
why a peer rejects TCP SYNs (ACL rejection, shields up, and in the
future: nothing listening, something listening on that port but wrong
interface, etc)
Updates #1094
Updates tailscale/corp#1185
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The compiler is failing to draw the connection between
slice cap and slice len, so is missing some obvious BCE opportunities.
Give it a hint by making the cap equal to the length.
The generated code is smaller and cleaner, and a bit faster.
name old time/op new time/op delta
Decode/tcp4-8 12.2ns ± 1% 11.6ns ± 3% -5.31% (p=0.000 n=28+29)
Decode/tcp6-8 12.5ns ± 2% 11.9ns ± 2% -4.84% (p=0.000 n=30+30)
Decode/udp4-8 11.5ns ± 1% 11.1ns ± 1% -3.11% (p=0.000 n=25+24)
Decode/udp6-8 11.8ns ± 3% 11.4ns ± 1% -3.08% (p=0.000 n=30+26)
Decode/icmp4-8 11.0ns ± 3% 10.6ns ± 1% -3.38% (p=0.000 n=25+30)
Decode/icmp6-8 11.4ns ± 1% 11.1ns ± 2% -2.29% (p=0.000 n=27+30)
Decode/igmp-8 10.3ns ± 0% 10.0ns ± 1% -3.26% (p=0.000 n=19+23)
Decode/unknown-8 8.68ns ± 1% 8.38ns ± 1% -3.55% (p=0.000 n=28+29)
