That's already the default. Avoid the overhead of writing it on one
side and reading it on the other to do nothing.
Updates #cleanup (noticed while researching something else)
Change-Id: I449c88a022271afb9be5da876bfaf438fe5d3f58
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This PR plumbs through awareness of an IPv6 SNAT/masquerade address from the wire protocol
through to the low-level (tstun / wgengine). This PR is the first in two PRs for implementing
IPv6 NAT support to/from peers.
A subsequent PR will implement the data-plane changes to implement IPv6 NAT - this is just plumbing.
Signed-off-by: Tom DNetto <tom@tailscale.com>
Updates ENG-991
This makes `omitempty` actually work, and saves bytes in each map response.
Updates tailscale/corp#8020
Signed-off-by: Maisem Ali <maisem@tailscale.com>
This adds support to make exit nodes and subnet routers work
when in scenarios where NAT is required.
It also updates the NATConfig to be generated from a `wgcfg.Config` as
that handles merging prefs with the netmap, so it has the required information
about whether an exit node is already configured and whether routes are accepted.
Updates tailscale/corp#8020
Signed-off-by: Maisem Ali <maisem@tailscale.com>
The log ID types were moved to a separate package so that
code that only depend on log ID types do not need to link
in the logic for the logtail client itself.
Not all code need the logtail client.
Signed-off-by: Joe Tsai <joetsai@digital-static.net>
This updates all source files to use a new standard header for copyright
and license declaration. Notably, copyright no longer includes a date,
and we now use the standard SPDX-License-Identifier header.
This commit was done almost entirely mechanically with perl, and then
some minimal manual fixes.
Updates #6865
Signed-off-by: Will Norris <will@tailscale.com>
The node and domain audit log IDs are provided in the map response,
but are ultimately going to be used in wgengine since
that's the layer that manages the tstun.Wrapper.
Do the plumbing work to get this field passed down the stack.
Signed-off-by: Joe Tsai <joetsai@digital-static.net>
In rare circumstances (tailscale/corp#3016), the PublicKey
and Endpoints can diverge.
This by itself doesn't cause any harm, but our early exit
in response did, because it prevented us from recovering from it.
Remove the early exit.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Instead of using the legacy codepath, teach discoEndpoint to handle
peers that have a home DERP, but no disco key. We can still communicate
with them, but only over DERP.
Signed-off-by: David Anderson <danderson@tailscale.com>
magicsock.Conn.ParseEndpoint requires a peer's public key,
disco key, and legacy ip/ports in order to do its job.
We currently accomplish that by:
* adding the public key in our wireguard-go fork
* encoding the disco key as magic hostname
* using a bespoke comma-separated encoding
It's a bit messy.
Instead, switch to something simpler: use a json-encoded struct
containing exactly the information we need, in the form we use it.
Our wireguard-go fork still adds the public key to the
address when it passes it to ParseEndpoint, but now the code
compensating for that is just a couple of simple, well-commented lines.
Once this commit is in, we can remove that part of the fork
and remove the compensating code.
Signed-off-by: Josh Bleecher Snyder <josharian@gmail.com>
Upstream wireguard-go renamed the interface method
from CreateEndpoint to ParseEndpoint.
I missed some comments. Fix them.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
For historical reasons, we ended up with two near-duplicate
copies of curve25519 key types, one in the wireguard-go module
(wgcfg) and one in the tailscale module (types/wgkey).
Then we moved wgcfg to the tailscale module.
We can now remove the wgcfg key type in favor of wgkey.
Signed-off-by: Josh Bleecher Snyder <josharian@gmail.com>
We don't use the port that wireguard-go passes to us (via magicsock.connBind.Open).
We ignore it entirely and use the port we selected.
When we tell wireguard-go that we're changing the listen_port,
it calls connBind.Close and then connBind.Open.
And in the meantime, it stops calling the receive functions,
which means that we stop receiving and processing UDP and DERP packets.
And that is Very Bad.
That was never a problem prior to b3ceca1dd7,
because we passed the SkipBindUpdate flag to our wireguard-go fork,
which told wireguard-go not to re-bind on listen_port changes.
That commit eliminated the SkipBindUpdate flag.
We could write a bunch of code to work around the gap.
We could add background readers that process UDP and DERP packets when wireguard-go isn't.
But it's simpler to never create the conditions in which wireguard-go rebinds.
The other scenario in which wireguard-go re-binds is device.Down.
Conveniently, we never call device.Down. We go from device.Up to device.Close,
and the latter only when we're shutting down a magicsock.Conn completely.
Rubber-ducked-by: Avery Pennarun <apenwarr@tailscale.com>
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
This is mostly code movement from the wireguard-go repo.
Most of the new wgcfg package corresponds to the wireguard-go wgcfg package.
wgengine/wgcfg/device{_test}.go was device/config{_test}.go.
There were substantive but simple changes to device_test.go to remove
internal package device references.
The API of device.Config (now wgcfg.DeviceConfig) grew an error return;
we previously logged the error and threw it away.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
