The block-write and block-read tests are both flaky,
because each assumes it can get a normal read/write
completed within 10ms. This isn’t always true.
We can’t increase the timeouts, because that slows down the test.
However, we don’t need to issue a regular read/write for this test.
The immediately preceding tests already test this code,
using a far more generous timeout.
Remove the extraneous read/write.
This drops the failure rate from 1 per 20,000 to undetectable
on my machine.
While we’re here, fix a typo in a debug print statement.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Without the continue, we might overwrite our current meta
with a zero meta.
Log the error, so that we can check for anything unexpected.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Currently, comments in resolv.conf cause our parser to fail,
with error messages like:
ParseIP("192.168.0.100 # comment"): unexpected character (at " # comment")
Fix that.
Noticed while looking through logs.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
When this happens, it is incredibly noisy in the logs.
It accounts for about a third of all remaining
"unexpected" log lines from a recent investigation.
It's not clear that we know how to fix this,
we have a functioning workaround,
and we now have a (cheap and efficient) metric for this
that we can use for measurements.
So reduce the logging to approximately once per minute.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
One of the most common "unexpected" log lines is:
"network state changed, but stringification didn't"
One way that this can occur is if an interesting interface
(non-Tailscale, has interesting IP address)
gains or loses an uninteresting IP address (link local or loopback).
The fact that the interface is interesting is enough for EqualFiltered
to inspect it. The fact that an IP address changed is enough for
EqualFiltered to declare that the interfaces are not equal.
But the State.String method reasonably declines to print any
uninteresting IP addresses. As a result, the network state appears
to have changed, but the stringification did not.
The String method is correct; nothing interesting happened.
This change fixes this by adding an IP address filter to EqualFiltered
in addition to the interface filter. This lets the network monitor
ignore the addition/removal of uninteresting IP addresses.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
The Windows BOOL type is an int32. We were using a bool,
which is a one byte wide. This could be responsible for the
ERROR_INVALID_PARAMETER errors we were seeing for calls to
WinHttpGetProxyForUrl.
We manually checked all other existing Windows syscalls
for similar mistakes and did not find any.
Updates #879
Co-authored-by: Aaron Klotz <aaron@tailscale.com>
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
There are lots of lines in the logs of the form:
portmapper: unexpected PMP probe response: {OpCode:128 ResultCode:3
SecondsSinceEpoch:NNN MappingValidSeconds:0 InternalPort:0
ExternalPort:0 PublicAddr:0.0.0.0}
ResultCode 3 here means a network failure, e.g. the NAT box itself has
not obtained a DHCP lease. This is not an indication that something
is wrong in the Tailscale client, so use different wording here
to reflect that. Keep logging, so that we can analyze and debug
the reasons that PMP probes fail.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Lets the systemd-resolved OSConfigurator report health changes
for out of band config resyncs.
Updates #3327
Signed-off-by: David Anderson <danderson@tailscale.com>
Don't set all the *.arpa. reverse DNS lookup domains if systemd-resolved
is old and can't handle them.
Fixes#3188
Change-Id: I283f8ce174daa8f0a972ac7bfafb6ff393dde41d
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
There are a few remaining uses of testing.AllocsPerRun:
Two in which we only log the number of allocations,
and one in which dynamically calculate the allocations
target based on a different AllocsPerRun run.
This also allows us to tighten the "no allocs"
test in wgengine/filter.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Now that we multicast the SSDP query, we can get IGD offers from
devices other than the current device's default gateway. We don't want
to accidentally bind ourselves to those.
Updates #3197
Signed-off-by: David Anderson <danderson@tailscale.com>
And the derper change to add a CORS endpoint for latency measurement.
And a little magicsock change to cut down some log spam on js/wasm.
Updates #3157
Change-Id: I5fd9e6f5098c815116ddc8ac90cbcd0602098a48
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
There are /etc/resolv.conf files out there where resolvconf wrote
the file but pointed to systemd-resolved as the nameserver.
We're better off handling those as systemd-resolved.
> # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
> # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
> # 127.0.0.53 is the systemd-resolved stub resolver.
> # run "systemd-resolve --status" to see details about the actual nameservers.
Fixes https://github.com/tailscale/tailscale/issues/3026
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
In some containers, /etc/resolv.conf is a bind-mount from outside the container.
This prevents renaming to or from /etc/resolv.conf, because it's on a different
filesystem from linux's perspective. It also prevents removing /etc/resolv.conf,
because doing so would break the bind-mount.
If we find ourselves within this environment, fall back to using copy+delete when
renaming to /etc/resolv.conf, and copy+truncate when renaming from /etc/resolv.conf.
Fixes#3000
Co-authored-by: Denton Gentry <dgentry@tailscale.com>
Signed-off-by: David Anderson <danderson@tailscale.com>
The "go generate" command blindly looks for "//go:generate" anywhere
in the file regardless of whether it is truly a comment.
Prevent this false positive in cloner.go by mangling the string
to look less like "//go:generate".
Signed-off-by: Joe Tsai <joetsai@digital-static.net>
