Port 0 is interpreted, per the spec (but inconsistently among router
software) as requesting to map every single available port on the UPnP
gateway to the internal IP address. We'd previously avoided picking
ports below 1024 for one of the two UPnP methods (in #7457), and this
change moves that logic so that we avoid it in all cases.
Updates #8992
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I20d652c0cd47a24aef27f75c81f78ae53cc3c71e
On some platforms (notably macOS and iOS) we look up the default
interface to bind outgoing connections to. This is both duplicated
work and results in logspam when the default interface is not available
(i.e. when a phone has no connectivity, we log an error and thus cause
more things that we will try to upload and fail).
Fixed by passing around a netmon.Monitor to more places, so that we can
use its cached interface state.
Fixes#7850
Updates #7621
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
We were previously sending a lower-case "udp" protocol, whereas other
implementations like miniupnp send an upper-case "UDP" protocol. For
compatibility, use an upper-case protocol instead.
Updates #7377
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I4aed204f94e4d51b7a256d29917af1536cb1b70f
Some devices don't let you UPnP portmap a port below 1024, so let's just
avoid that range of ports entirely.
Updates #7377
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: Ib7603b1c9a019162cdc4fa21744a2cae48bb1d86
The debug flag on tailscaled isn't available in the macOS App Store
build, since we don't have a tailscaled binary; move it to the
'tailscale debug' CLI that is available on all platforms instead,
accessed over LocalAPI.
Updates #7377
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I47bffe4461e036fab577c2e51e173f4003592ff7
This updates all source files to use a new standard header for copyright
and license declaration. Notably, copyright no longer includes a date,
and we now use the standard SPDX-License-Identifier header.
This commit was done almost entirely mechanically with perl, and then
some minimal manual fixes.
Updates #6865
Signed-off-by: Will Norris <will@tailscale.com>
Gateway devices operating as an HA pair w/VRRP or CARP may send UPnP
replies from static addresses rather than the floating gateway address.
This commit relaxes our source address verification such that we parse
responses from non-gateway IPs, and re-point the UPnP root desc
URL to the gateway IP. This ensures we are still interfacing with the
gateway device (assuming L2 security intact), even though we got a
root desc from a non-gateway address.
This relaxed handling is required for ANY port mapping to work on certain
OPNsense/pfsense distributions using CARP at the time of writing, as
miniupnpd may only listen on the static, non-gateway interface address
for PCP and PMP.
Fixes#5502
Signed-off-by: Jordan Whited <jordan@tailscale.com>
The //go:build syntax was introduced in Go 1.17:
https://go.dev/doc/go1.17#build-lines
gofmt has kept the +build and go:build lines in sync since
then, but enough time has passed. Time to remove them.
Done with:
perl -i -npe 's,^// \+build.*\n,,' $(git grep -l -F '+build')
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
In the 1.27 unstable releases we set the min-version to iOS15,
which means we have 50 MBytes of RAM in the Network Extension.
https://tailscale.com/blog/go-linker/
Include the UPnP/NAT-PMP/PCP portmapper support now that there
is memory for it.
Fixes https://github.com/tailscale/tailscale/issues/2495
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
This logs some basic statistics for UPnP, so that tailscale can better understand what routers
are being used and how to connect to them.
Signed-off-by: julianknodt <julianknodt@gmail.com>
Prior to Tailscale 1.12 it detected UPnP on any port.
Starting with Tailscale 1.11.x, it stopped detecting UPnP on all ports.
Then start plumbing its discovered Location header port number to the
code that was assuming port 5000.
Fixes#2109
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Previously, this was incorrectly returning the internal port, and using that with the external
exposed IP when it did not use WANIPConnection2. In the case when we must provide a port, we
return it instead.
Noticed this while implementing the integration test for upnp.
Signed-off-by: julianknodt <julianknodt@gmail.com>
Add in UPnP portmapping, using goupnp library in order to get the UPnP client and run the
portmapping functions. This rips out anywhere where UPnP used to be in portmapping, and has a
flow separate from PMP and PCP.
RELNOTE=portmapper now supports UPnP mappings
Fixes#682
Updates #2109
Signed-off-by: julianknodt <julianknodt@gmail.com>
