The AddSNATRuleForDst rule was adding a new rule each time it was called including:
- if a rule already existed
- if a rule matching the destination, but with different desired source already existed
This was causing issues especially for the in-progress egress HA proxies work,
where the rules are now refreshed more frequently, so more redundant rules
were being created.
This change:
- only creates the rule if it doesn't already exist
- if a rule for the same dst, but different source is found, delete it
- also ensures that egress proxies refresh firewall rules
if the node's tailnet IP changes
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* cmd/containerboot,kube,util/linuxfw: configure kube egress proxies to route to 1+ tailnet targets
This commit is first part of the work to allow running multiple
replicas of the Kubernetes operator egress proxies per tailnet service +
to allow exposing multiple tailnet services via each proxy replica.
This expands the existing iptables/nftables-based proxy configuration
mechanism.
A proxy can now be configured to route to one or more tailnet targets
via a (mounted) config file that, for each tailnet target, specifies:
- the target's tailnet IP or FQDN
- mappings of container ports to which cluster workloads will send traffic to
tailnet target ports where the traffic should be forwarded.
Example configfile contents:
{
"some-svc": {"tailnetTarget":{"fqdn":"foo.tailnetxyz.ts.net","ports"{"tcp:4006:80":{"protocol":"tcp","matchPort":4006,"targetPort":80},"tcp:4007:443":{"protocol":"tcp","matchPort":4007,"targetPort":443}}}}
}
A proxy that is configured with this config file will configure firewall rules
to route cluster traffic to the tailnet targets. It will then watch the config file
for updates as well as monitor relevant netmap updates and reconfigure firewall
as needed.
This adds a bunch of new iptables/nftables functionality to make it easier to dynamically update
the firewall rules without needing to restart the proxy Pod as well as to make
it easier to debug/understand the rules:
- for iptables, each portmapping is a DNAT rule with a comment pointing
at the 'service',i.e:
-A PREROUTING ! -i tailscale0 -p tcp -m tcp --dport 4006 -m comment --comment "some-svc:tcp:4006 -> tcp:80" -j DNAT --to-destination 100.64.1.18:80
Additionally there is a SNAT rule for each tailnet target, to mask the source address.
- for nftables, a separate prerouting chain is created for each tailnet target
and all the portmapping rules are placed in that chain. This makes it easier
to look up rules and delete services when no longer needed.
(nftables allows hooking a custom chain to a prerouting hook, so no extra work
is needed to ensure that the rules in the service chains are evaluated).
The next steps will be to get the Kubernetes Operator to generate
the configfile and ensure it is mounted to the relevant proxy nodes.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
And update a few callers as examples of motivation. (there are a
couple others, but these are the ones where it's prettier)
Updates #cleanup
Change-Id: Ic8c5cb7af0a59c6e790a599136b591ebe16d38eb
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
When the desired netfilter mode was unset, we would always try
to use the `iptables` binary. In such cases if iptables was not found,
tailscaled would just crash as seen in #13440. To work around this, in those
cases check if the `iptables` binary even exists and if it doesn't fall back
to the nftables implementation.
Verified that it works on stock Ubuntu 24.04.
Updates #5621
Updates #8555
Updates #8762Fixes#13440
Signed-off-by: Maisem Ali <maisem@tailscale.com>
It was returning a nil `*iptablesRunner` instead of a
nil `NetfilterRunner` interface which would then fail
checks later.
Fixes#13012
Signed-off-by: Maisem Ali <maisem@tailscale.com>
cmd/containerboot,cmd/k8s-operator: enable IPv6 for fqdn egress proxies
Don't skip installing egress forwarding rules for IPv6 (as long as the host
supports IPv6), and set headless services `ipFamilyPolicy` to
`PreferDualStack` to optionally enable both IP families when possible. Note
that even with `PreferDualStack` set, testing a dual-stack GKE cluster with
the default DNS setup of kube-dns did not correctly set both A and
AAAA records for the headless service, and instead only did so when
switching the cluster DNS to Cloud DNS. For both IPv4 and IPv6 to work
simultaneously in a dual-stack cluster, we require headless services to
return both A and AAAA records.
If the host doesn't support IPv6 but the FQDN specified only has IPv6
addresses available, containerboot will exit with error code 1 and an
error message because there is no viable egress route.
Fixes#12215
Signed-off-by: Tom Proctor <tomhjp@users.noreply.github.com>
* util/linuxfw: fix IPv6 NAT availability check for nftables
When running firewall in nftables mode,
there is no need for a separate NAT availability check
(unlike with iptables, there are no hosts that support nftables, but not IPv6 NAT - see tailscale/tailscale#11353).
This change fixes a firewall NAT availability check that was using the no-longer set ipv6NATAvailable field
by removing the field and using a method that, for nftables, just checks that IPv6 is available.
Updates tailscale/tailscale#12008
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
This PR bumps iptables to a newer version that has a function to detect
'NotExists' errors and uses that function to determine whether errors
received on iptables rule and chain clean up are because the rule/chain
does not exist- if so don't log the error.
Updates corp#19336
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* cmd/containerboot,util/linuxfw: support proxy backends specified by DNS name
Adds support for optionally configuring containerboot to proxy
traffic to backends configured by passing TS_EXPERIMENTAL_DEST_DNS_NAME env var
to containerboot.
Containerboot will periodically (every 10 minutes) attempt to resolve
the DNS name and ensure that all traffic sent to the node's
tailnet IP gets forwarded to the resolved backend IP addresses.
Currently:
- if the firewall mode is iptables, traffic will be load balanced
accross the backend IP addresses using round robin. There are
no health checks for whether the IPs are reachable.
- if the firewall mode is nftables traffic will only be forwarded
to the first IP address in the list. This is to be improved.
* cmd/k8s-operator: support ExternalName Services
Adds support for exposing endpoints, accessible from within
a cluster to the tailnet via DNS names using ExternalName Services.
This can be done by annotating the ExternalName Service with
tailscale.com/expose: "true" annotation.
The operator will deploy a proxy configured to route tailnet
traffic to the backend IPs that service.spec.externalName
resolves to. The backend IPs must be reachable from the operator's
namespace.
Updates tailscale/tailscale#10606
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
This removes a potentially increased boot delay for certain boot
topologies where they block on ExecStartPre that may have socket
activation dependencies on other system services (such as
systemd-resolved and NetworkManager).
Also rename cleanup to clean up in affected/immediately nearby places
per code review commentary.
Fixes#11599
Signed-off-by: James Tucker <james@tailscale.com>
MSS clamping for nftables was mostly not ran due to to an earlier rule in the FORWARD chain issuing accept verdict.
This commit places the clamping rule into a chain of its own to ensure that it gets ran.
Updates tailscale/tailscale#11002
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
We have hosts that support IPv6, but not IPv6 firewall configuration
in iptables mode.
We also have hosts that have some support for IPv6 firewall
configuration in iptables mode, but do not have iptables filter table.
We should:
- configure ip rules for all hosts that support IPv6
- only configure firewall rules in iptables mode if the host
has iptables filter table.
Updates tailscale/tailscale#11540
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
There are container environments such as GitHub codespaces that have
partial IPv6 support - routing support is enabled at the kernel level,
but lacking IPv6 filter support in the iptables module.
In the specific example of the codespaces environment, this also has
pre-existing legacy iptables rules in the IPv4 tables, as such the
nascent firewall mode detection will always pick iptables.
We would previously fault trying to install rules to the filter table,
this catches that condition earlier, and disables IPv6 support under
these conditions.
Updates #5621
Updates #11344
Updates #11354
Signed-off-by: James Tucker <james@tailscale.com>
Ensure that the latest DNATNonTailscaleTraffic rule
gets inserted on top of any pre-existing rules.
Updates tailscale/tailscale#11281
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Ensure that if getOrCreateChain creates a new chain, it actually returns the created chain
Updates tailscale/tailscale#10399
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* util/linuxfw, wgengine: allow ingress to magicsock UDP port on Linux
Updates #9084.
Currently, we have to tell users to manually open UDP ports on Linux when
certain firewalls (like ufw) are enabled. This change automates the process of
adding and updating those firewall rules as magicsock changes what port it
listens on.
Signed-off-by: Naman Sood <mail@nsood.in>
We were previously using the netlink API to see if there are chains/rules that
already exist. This works fine in environments where there is either full
nftable support or no support at all. However, we have identified certain
environments which have partial nftable support and the only feasible way of
detecting such an environment is to try to create some of the chains that we
need.
This adds a check to create a dummy postrouting chain which is immediately
deleted. The goal of the check is to ensure we are able to use nftables and
that it won't error out later. This check is only done in the path where we
detected that the system has no preexisting nftable rules.
Updates #5621
Updates #8555
Updates #8762
Signed-off-by: Maisem Ali <maisem@tailscale.com>
These tests were broken at HEAD. CI currently does not run these
as root, will figure out how to do that in a followup.
Updates #5621
Updates #8555
Updates #8762
Signed-off-by: Maisem Ali <maisem@tailscale.com>
This migrates containerboot to reuse the NetfilterRunner used
by tailscaled instead of manipulating iptables rule itself.
This has the added advantage of now working with nftables and
we can potentially drop the `iptables` command from the container
image in the future.
Updates #9310
Co-authored-by: Irbe Krumina <irbe@tailscale.com>
Signed-off-by: Maisem Ali <maisem@tailscale.com>
This allows using the fake runner in different packages
that need to manage filter rules.
Updates #cleanup
Signed-off-by: Maisem Ali <maisem@tailscale.com>
Just a refactor to consolidate the firewall detection logic in a single
package so that it can be reused in a later commit by containerboot.
Updates #9310
Signed-off-by: Maisem Ali <maisem@tailscale.com>
Add an explicit accept rule for input to the tun interface, as a mirror
to the explicit rule to accept output from the tun interface.
The rule matches any packet in to our tun interface and accepts it, and
the rule is positioned and prioritized such that it should be evaluated
prior to conventional ufw/iptables/nft rules.
Updates #391Fixes#7332
Updates #9084
Signed-off-by: James Tucker <james@tailscale.com>
Appears to be a missing nil handling case. I looked back over other
usage of findRule and the others all have nil guards. findRule returns
nil when no rules are found matching the arguments.
Fixes#9553
Signed-off-by: James Tucker <james@tailscale.com>
Replace %w verb with %v verb when logging errors.
Use %w only for wrapping errors with fmt.Errorf()
Fixes: #9213
Signed-off-by: Craig Rodrigues <rodrigc@crodrigues.org>
And flesh it out and use idiomatic doc style ("whether" for bools)
and end in a period while there anyway.
Updates #cleanup
Change-Id: Ieb82f13969656e2340c3510e7b102dc8e6932611
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This commit tries to mimic the way iptables-nft work with the filewall rules. We
follow the convention of using tables like filter, nat and the conventional
chains, to make our nftables implementation work with ufw.
Updates: #391
Signed-off-by: KevinLiang10 <kevinliang@tailscale.com>
Go style is for error variables to start with "err" (or "Err")
and for error types to end in "Error".
Updates #cleanup
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This commit replaces the TS_DEBUG_USE_NETLINK_NFTABLES envknob with
a TS_DEBUG_FIREWALL_MODE that should be set to either 'iptables' or
'nftables' to select firewall mode manually, other wise tailscaled
will automatically choose between iptables and nftables depending on
environment and system availability.
updates: #319
Signed-off-by: KevinLiang10 <kevinliang@tailscale.com>
The util/linuxfw/iptables.go had a bunch of code that wasn't yet used
(in prep for future work) but because of its imports, ended up
initializing code deep within gvisor that panicked on init on arm64
systems not using 4KB pages.
This deletes the unused code to delete the imports and remove the
panic. We can then cherry-pick this back to the branch and restore it
later in a different way.
A new test makes sure we don't regress in the future by depending on
the panicking package in question.
Fixes#8658
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This commit adds nftable rule injection for tailscaled. If tailscaled is
started with envknob TS_DEBUG_USE_NETLINK_NFTABLES = true, the router
will use nftables to manage firewall rules.
Updates: #391
Signed-off-by: KevinLiang10 <kevinliang@tailscale.com>
Exclide GOARCHs including: mips, mips64, mips64le, mipsle, riscv64.
These archs are not supported by gvisor.dev/gvisor/pkg/hostarch.
Fixes: #391
Signed-off-by: KevinLiang10 <kevinliang@tailscale.com>
This change is introducing new netfilterRunner interface and moving iptables manipulation to a lower leveled iptables runner.
For #391
Signed-off-by: KevinLiang10 <kevinliang@tailscale.com>
This isn't currently supported due to missing support in upstream
dependencies, and also we don't use this package anywhere right now.
Just conditionally skip this for now.
Fixes#7268
Change-Id: Ie7389c2c0816b39b410c02a7276051a4c18b6450
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
