This removes a potentially increased boot delay for certain boot
topologies where they block on ExecStartPre that may have socket
activation dependencies on other system services (such as
systemd-resolved and NetworkManager).
Also rename cleanup to clean up in affected/immediately nearby places
per code review commentary.
Fixes#11599
Signed-off-by: James Tucker <james@tailscale.com>
At least in the case of dialing a Tailscale IP.
Updates #4529
Change-Id: I9fd667d088a14aec4a56e23aabc2b1ffddafa3fe
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Updates #7946
[@bradfitz fixed up version of #8417]
Change-Id: I1dbf6fa8d525b25c0d7ad5c559a7f937c3cd142a
Signed-off-by: alexelisenko <39712468+alexelisenko@users.noreply.github.com>
Signed-off-by: Alex Paguis <alex@windscribe.com>
The netcheck package and the magicksock package coordinate via the
health package, but both sides have time based heuristics through
indirect dependencies. These were misaligned, so the implemented
heuristic aimed at reducing DERP moves while there is active traffic
were non-operational about 3/5ths of the time.
It is problematic to setup a good test for this integration presently,
so instead I added comment breadcrumbs along with the initial fix.
Updates #8603
Signed-off-by: James Tucker <james@tailscale.com>
We now allow some more ICMP errors to flow, specifically:
- ICMP parameter problem in both IPv4 and IPv6 (corrupt headers)
- ICMP Packet Too Big (for IPv6 PMTU)
Updates #311
Updates #8102
Updates #11002
Signed-off-by: James Tucker <james@tailscale.com>
This implementation uses less memory than tempfork/device,
which helps avoid OOM conditions in the iOS VPN extension when
switching to a Tailnet with ExitNode routing enabled.
Updates tailscale/corp#18514
Signed-off-by: Percy Wegmann <percy@tailscale.com>
I was running all tests while preparing a recent stable release, and
this was failing because my computer is connected to a fairly large
tailnet.
```
--- FAIL: TestGetRouteTable (0.01s)
routetable_linux_test.go:32: expected at least one default route;
...
```
```
$ ip route show table 52 | wc -l
1051
```
Updates #cleanup
Signed-off-by: Anton Tolchanov <anton@tailscale.com>
This test could hang because the subprocess was blocked on writing to
the stdout pipe if we find the address we're looking for early in the
output.
Updates #cleanup
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I68d82c22a5d782098187ae6d8577e43063b72573
The `stack.PacketBufferPtr` type no longer exists; replace it with
`*stack.PacketBuffer` instead.
Updates #8043
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: Ib56ceff09166a042aa3d9b80f50b2aa2d34b3683
When reverse path filtering is in strict mode on Linux, using an exit
node blocks all network connectivity. This change adds a warning about
this to `tailscale status` and the logs.
Example in `tailscale status`:
```
- not connected to home DERP region 22
- The following issues on your machine will likely make usage of exit nodes impossible: [interface "eth0" has strict reverse-path filtering enabled], please set rp_filter=2 instead of rp_filter=1; see https://github.com/tailscale/tailscale/issues/3310
```
Example in the logs:
```
2024/02/21 21:17:07 health("overall"): error: multiple errors:
not in map poll
The following issues on your machine will likely make usage of exit nodes impossible: [interface "eth0" has strict reverse-path filtering enabled], please set rp_filter=2 instead of rp_filter=1; see https://github.com/tailscale/tailscale/issues/3310
```
Updates #3310
Signed-off-by: Anton Tolchanov <anton@tailscale.com>
Tailscaled becomes inoperative if the Tailscale Tunnel wintun adapter is abruptly removed.
wireguard-go closes the device in case of a read error, but tailscaled keeps running.
This adds detection of a closed WireGuard device, triggering a graceful shutdown of tailscaled.
It is then restarted by the tailscaled watchdog service process.
Fixes#11222
Signed-off-by: Nick Khyl <nickk@tailscale.com>
The WinTun adapter may have been removed by the time we're closing
the dns.windowsManager, and its associated interface registry key might
also have been deleted. We shouldn't use winutil.OpenKeyWait and wait
for the interface key to appear when performing a cleanup as a part of
the windowsManager shutdown.
Updates #11222
Signed-off-by: Nick Khyl <nickk@tailscale.com>
If a client socket is remotely lost but the client is not sent an RST in
response to the next request, the socket might sit in RTO for extended
lengths of time, resulting in "no internet" for users. Instead, timeout
after 10s, which will close the underlying socket, recovering from the
situation more promptly.
Updates #10967
Signed-off-by: James Tucker <james@tailscale.com>
We don't need a log line every time defaultRoute is read in the good
case, and we now only log default interface updates that are actually
changes.
Updates #3363
Signed-off-by: James Tucker <james@tailscale.com>
Setting a user timeout will be a more practical tuning knob for a number
of endpoints, this provides a way to set it.
Updates tailscale/corp#17587
Signed-off-by: James Tucker <james@tailscale.com>
This fixes an infinite loop caused by the configuration of
systemd-resolved on Amazon Linux 2023 and how that interacts with
Tailscale's "direct" mode. We now drop the Tailscale service IP from the
OS's "base configuration" when we detect this configuration.
Updates #7816
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I73a4ea8e65571eb368c7e179f36af2c049a588ee
These are functionally the same as the "urn:schemas-upnp-org" services
with a few minor changes, and are still used by older devices. Support
them to improve our ability to obtain an external IP on such networks.
Updates #10911
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I05501fad9d6f0a3b8cf19fc95eee80e7d16cc2cf
This no longer results in a nil pointer exception when we get a valid
UPnP response with no supported clients.
Updates #10911
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I6e3715a49a193ff5261013871ad7fff197a4d77e
The prefix has space for 32-bit site IDs, but the validateViaPrefix
function would previously have disallowed site IDs greater than 255.
Fixestailscale/corp#16470
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I4cdb0711dafb577fae72d86c4014cf623fa538ef
Add a standalone server for STUN that can be hosted independently of the
derper, and factor that back into the derper.
Fixes#8434Closes#8435Closes#10745
Signed-off-by: James Tucker <james@tailscale.com>
To make it easier to correlate the starting/ending log messages.
Updates #cleanup
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I2802d53ad98e19bc8914bc58f8c04d4443227b26
Updates #8022
Updates #6075
On iOS, we currently rely on delegated interface information to figure out the default route interface. The NetworkExtension framework in iOS seems to set the delegate interface only once, upon the *creation* of the VPN tunnel. If a network transition (e.g. from Wi-Fi to Cellular) happens while the tunnel is connected, it will be ignored and we will still try to set Wi-Fi as the default route because the delegated interface is not getting updated as connectivity transitions.
Here we work around this on the Swift side with a NWPathMonitor instance that observes the interface name of the first currently satisfied network path. Our Swift code will call into `UpdateLastKnownDefaultRouteInterface`, so we can rely on that when it is set.
If for any reason the Swift machinery didn't work and we don't get any updates, here we also have some fallback logic: we try finding a hardcoded Wi-Fi interface called en0. If en0 is down, we fall back to cellular (pdp_ip0) as a last resort. This doesn't handle all edge cases like USB-Ethernet adapters or multiple Ethernet interfaces, but it is good enough to ensure connectivity isn't broken.
I tested this on iPhones and iPads running iOS 17.1 and it appears to work. Switching between different cellular plans on a dual SIM configuration also works (the interface name remains pdp_ip0).
Signed-off-by: Andrea Gottardo <andrea@tailscale.com>
If the epoch that we see during a Probe is less than the existing epoch,
it means that the gateway has either restarted or reset its
configuration, and an existing mapping is no longer valid. Reset any
saved mapping(s) if we detect this case so that a future
createOrGetMapping will not attempt to re-use it.
Updates #10597
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: Ie3cddaf625cb94a29885f7a1eeea25dbf6b97b47
When the portable Monitor creates a winMon via newOSMon, we register
address and route change callbacks with Windows. Once a callback is hit,
it starts a goroutine that attempts to send the event into messagec and returns.
The newly started goroutine then blocks until it can send to the channel.
However, if the monitor is never started and winMon.Receive is never called,
the goroutines remain indefinitely blocked, leading to goroutine leaks and
significant memory consumption in the tailscaled service process on Windows.
Unlike the tailscaled subprocess, the service process creates but never starts
a Monitor.
This PR adds a check within the callbacks to confirm the monitor's active status,
and exits immediately if the monitor hasn't started.
Updates #9864
Signed-off-by: Nick Khyl <nickk@tailscale.com>
Run `staticcheck` with `U1000` to find unused code. This cleans up about
a half of it. I'll do the other half separately to keep PRs manageable.
Updates #cleanup
Signed-off-by: Andrew Lytvynov <awly@tailscale.com>
This logs additional information about what mapping(s) are obtained
during the creation process, including whether we return an existing
cached mapping.
Updates #10597
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I9ff25071f064c91691db9ab0b9365ccc5f948d6e
Currently, we get the "likely home router" gateway IP and then iterate
through all IPs for all interfaces trying to match IPs to determine the
source IP. However, on many platforms we know what interface the gateway
is through, and thus we don't need to iterate through all interfaces
checking IPs. Instead, use the IP address of the associated interface.
This better handles the case where we have multiple interfaces on a
system all connected to the same gateway, and where the first interface
that we visit (as iterated by ForeachInterfaceAddress) isn't also the
default internet route.
Updates #8992
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I8632f577f1136930f4ec60c76376527a19a47d1f
Instead of taking the first UPnP response we receive and using that to
create port mappings, store all received UPnP responses, sort and
deduplicate them, and then try all of them to obtain an external
address.
Updates #10602
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I783ccb1834834ee2a9ecbae2b16d801f2354302f
This uses the fact that we've received a frame from a given DERP region
within a certain time as a signal that the region is stil present (and
thus can still be a node's PreferredDERP / home region) even if we don't
get a STUN response from that region during a netcheck.
This should help avoid DERP flaps that occur due to losing STUN probes
while still having a valid and active TCP connection to the DERP server.
RELNOTE=Reduce home DERP flapping when there's still an active connection
Updates #8603
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: If7da6312581e1d434d5c0811697319c621e187a0
Previously, we would select the first WANIPConnection2 (and related)
client from the root device, without any additional checks. However,
some routers expose multiple UPnP devices in various states, and simply
picking the first available one can result in attempting to perform a
portmap with a device that isn't functional.
Instead, mimic what the miniupnpc code does, and prefer devices that are
(a) reporting as Connected, and (b) have a valid external IP address.
For our use-case, we additionally prefer devices that have an external
IP address that's a public address, to increase the likelihood that we
can obtain a direct connection from peers.
Finally, we split out fetching the root device (getUPnPRootDevice) from
selecting the best service within that root device (selectBestService),
and add some extensive tests for various UPnP server behaviours.
RELNOTE=Improve UPnP portmapping when multiple UPnP services exist
Updates #8364
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I71795cd80be6214dfcef0fe83115a5e3fe4b8753
Unfortunately in the test we can't reproduce the failure seen
in the real system ("SOAP fault: UPnPError")
Updates https://github.com/tailscale/tailscale/issues/8364
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
Before this fix, LikelyHomeRouterIP could return a 'self' IP that
doesn't correspond to the gateway address, since it picks the first
private address when iterating over the set interfaces as the 'self' IP,
without checking that the address corresponds with the
previously-detected gateway.
This behaviour was introduced by accident in aaf2df7, where we deleted
the following code:
for _, prefix := range privatev4s {
if prefix.Contains(gateway) && prefix.Contains(ip) {
myIP = ip
ok = true
return
}
}
Other than checking that 'gateway' and 'ip' were private IP addresses
(which were correctly replaced with a call to the netip.Addr.IsPrivate
method), it also implicitly checked that both 'gateway' and 'ip' were a
part of the *same* prefix, and thus likely to be the same interface.
Restore that behaviour by explicitly checking pfx.Contains(gateway),
which, given that the 'ip' variable is derived from our prefix 'pfx',
ensures that the 'self' IP will correspond to the returned 'gateway'.
Fixes#10466
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: Iddd2ee70cefb9fb40071986fefeace9ca2441ee6
Config.singleResolverSet returns true if all routes have the same resolvers,
even if the routes have no resolvers. If none of the routes have a specific
resolver, the default should be used instead. Therefore, check for more than
0 instead of nil.
Signed-off-by: Ryan Petris <ryan@petris.net>
This prevents running more than one recursive resolution for the same
hostname in parallel, which can use excessive amounts of CPU when called
in a tight loop. Additionally, add tests that hit the network (when
run with a flag) to test the lookup behaviour.
Updates tailscale/corp#15261
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I39351e1d2a8782dd4c52cb04b3bd982eb651c81e
An EmbeddedAppConnector is added that when configured observes DNS
responses from the PeerAPI. If a response is found matching a configured
domain, routes are advertised when necessary.
The wiring from a configuration in the netmap capmap is not yet done, so
while the connector can be enabled, no domains can yet be added.
Updates tailscale/corp#15437
Signed-off-by: James Tucker <james@tailscale.com>
The other IP types don't appear to be imported anymore, and after a scan
through I couldn't see any substantial usage of other representations,
so I think this TODO is complete.
Updates #cleanup
Signed-off-by: James Tucker <james@tailscale.com>
As of 2023-11-27, the official IP addresses for b.root-servers.net will
change to a new set, with the older IP addresses supported for at least
a year after that date. These IPs are already active and returning
results, so update these in our recursive DNS resolver package so as to
be ready for the switchover.
See: https://b.root-servers.org/news/2023/05/16/new-addresses.htmlFixes#9994
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I29e2fe9f019163c9ec0e62bdb286e124aa90a487
It seems to be implicated in a CPU consumption bug that's not yet
understood. Disable it until we understand.
Updates tailscale/corp#15261
Change-Id: Ia6d0c310da6464dda79a70fc3c18be0782812d3f
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Endeavour OS, at least, uses NetworkManager 1.44.2 and does
not use systemd-resolved behind the scenes at all. If we
find ourselves in that situation, return "direct" not
"systemd-resolved"
Fixes https://github.com/tailscale/tailscale/issues/9687
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
The current structure meant that we were embedding netstack in
the tailscale CLI and in the GUIs. This removes that by isolating
the checksum munging to a different pkg which is only called from
`net/tstun`.
Fixes#9756
Signed-off-by: Maisem Ali <maisem@tailscale.com>
Tailscale attempts to determine if resolvconf or openresolv
is in use by running `resolvconf --version`, under the assumption
this command will error when run with Debian's resolvconf. This
assumption is no longer true and leads to the wrong commands being
run on newer versions of Debian with resolvconf >= 1.90. We can
now check if the returned version string starts with "Debian resolvconf"
if the command is successful.
Fixes#9218
Signed-off-by: Galen Guyer <galen@galenguyer.com>
Automatically probe the path MTU to a peer when peer MTU is enabled, but do not
use the MTU information for anything yet.
Updates #311
Signed-off-by: Val <valerie@tailscale.com>
Advertise it on Android (it looks like it already works once advertised).
And both advertise & likely fix it on iOS. Yet untested.
Updates #9672
Change-Id: If3b7e97f011dea61e7e75aff23dcc178b6cf9123
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Instead of just falling back to making a TCP query to an upstream DNS
server when the UDP query returns a truncated query, also start a TCP
query in parallel with the UDP query after a given race timeout. This
ensures that if the upstream DNS server does not reply over UDP (or if
the response packet is blocked, or there's an error), we can still make
queries if the server replies to TCP queries.
This also adds a new package, util/race, to contain the logic required for
racing two different functions and returning the first non-error answer.
Updates tailscale/corp#14809
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I4311702016c1093b1beaa31b135da1def6d86316
Implements the ability for the address-rewriting code to support rewriting IPv6 addresses.
Specifically, UpdateSrcAddr & UpdateDstAddr.
Signed-off-by: Tom DNetto <tom@tailscale.com>
Updates https://github.com/tailscale/corp/issues/11202
Now that corp is updated, remove the shim code to bridge the rename from
DefaultMTU() to DefaultTUNMTU.
Updates #311
Signed-off-by: Val <valerie@tailscale.com>
We should be able to freely run `./tool/go generate ./...`, but we're
continually dodging this particular generator. Instead of constantly
dodging it, let's just remove it.
Updates #cleanup
Signed-off-by: James Tucker <james@tailscale.com>
Prepare for path MTU discovery by splitting up the concept of
DefaultMTU() into the concepts of the Tailscale TUN MTU, MTUs of
underlying network interfaces, minimum "safe" TUN MTU, user configured
TUN MTU, probed path MTU to a peer, and maximum probed MTU. Add a set
of likely MTUs to probe.
Updates #311
Signed-off-by: Val <valerie@tailscale.com>
We weren't correctly retrying truncated requests to an upstream DNS
server with TCP. Instead, we'd return a truncated request to the user,
even if the user was querying us over TCP and thus able to handle a
large response.
Also, add an envknob and controlknob to allow users/us to disable this
behaviour if it turns out to be buggy (✨ DNS ✨).
Updates #9264
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: Ifb04b563839a9614c0ba03e9c564e8924c1a2bfd
Prepare for path MTU discovery by splitting up the concept of
DefaultMTU() into the concepts of the Tailscale TUN MTU, MTUs of
underlying network interfaces, minimum "safe" TUN MTU, user configured
TUN MTU, probed path MTU to a peer, and maximum probed MTU. Add a set
of likely MTUs to probe.
Updates #311
Signed-off-by: Val <valerie@tailscale.com>
One Quad9 IPv6 address was incorrect, and an additional group needed
adding. Additionally I checked Cloudflare and included source reference
URLs for both.
Updates #cleanup
Signed-off-by: James Tucker <james@tailscale.com>
It might as well have been spewing out gibberish. This adds
a nicer output format for us to be able to read and identify
whats going on.
Sample output
```
natV4Config{nativeAddr: 100.83.114.95, listenAddrs: [10.32.80.33], dstMasqAddrs: [10.32.80.33: 407 peers]}
```
Fixestailscale/corp#14650
Signed-off-by: Maisem Ali <maisem@tailscale.com>
This PR plumbs through awareness of an IPv6 SNAT/masquerade address from the wire protocol
through to the low-level (tstun / wgengine). This PR is the first in two PRs for implementing
IPv6 NAT support to/from peers.
A subsequent PR will implement the data-plane changes to implement IPv6 NAT - this is just plumbing.
Signed-off-by: Tom DNetto <tom@tailscale.com>
Updates ENG-991
This should allow us to gather a bit more information about errors that
we encounter when creating UPnP mappings. Since we don't have a
"LabelMap" construction for clientmetrics, do what sockstats does and
lazily register a new metric when we see a new code.
Updates #9343
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: Ibb5aadd6138beb58721f98123debcc7273b611ba
And convert all callers over to the methods that check SelfNode.
Now we don't have multiple ways to express things in tests (setting
fields on SelfNode vs NetworkMap, sometimes inconsistently) and don't
have multiple ways to check those two fields (often only checking one
or the other).
Updates #9443
Change-Id: I2d7ba1cf6556142d219fae2be6f484f528756e3c
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
NetworkMap.Addresses is redundant with the SelfNode.Addresses. This
works towards a TODO to delete NetworkMap.Addresses and replace it
with a method.
This is similar to #9389.
Updates #cleanup
Change-Id: Id000509ca5d16bb636401763d41bdb5f38513ba0
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The following IPs are not used anymore: 193.19.108.2 and 193.19.108.3.
All of the servers are now named consistently under dns.mullvad.net.
Several new servers were added.
https://mullvad.net/en/help/dns-over-https-and-dns-over-tls/
Updates #5416
Updates #9345
Signed-off-by: James Tucker <james@tailscale.com>
This logs that the gateway/self IP address has changed if one of the new
values differs.
Updates #8992
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I0919424b68ad97fbe1204dd36317ed6f5915411f
Some routers don't support lease times for UPnP portmapping; let's fall
back to adding a permanent lease in these cases. Additionally, add a
proper end-to-end test case for the UPnP portmapping behaviour.
Updates #9343
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I17dec600b0595a5bfc9b4d530aff6ee3109a8b12
Previously two tsnet nodes in the same process couldn't have disjoint
sets of controlknob settings from control as both would overwrite each
other's global variables.
This plumbs a new controlknobs.Knobs type around everywhere and hangs
the knobs sent by control on that instead.
Updates #9351
Change-Id: I75338646d36813ed971b4ffad6f9a8b41ec91560
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
I didn't clean up the more idiomatic map[T]bool with true values, at
least yet. I just converted the relatively awkward struct{}-valued
maps.
Updates #cleanup
Change-Id: I758abebd2bb1f64bc7a9d0f25c32298f4679c14f
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
RELNOTE=Adds support for Wikimedia DNS
Updates #9255
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I4213c29e0f91ea5aa0304a5a026c32b6690fead9
It was too aggressive before, as it only had the ill-defined "Major"
bool to work with. Now it can check more precisely.
Updates #9040
Change-Id: I20967283b64af6a9cad3f8e90cff406de91653b8
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This makes wsconn.Conns somewhat present reasonably when they are
the client of an http.Request, rather than just put a placeholder
in that field.
Updates tailscale/corp#13777
Signed-off-by: David Anderson <danderson@tailscale.com>
This removes a lot of API from net/interfaces (including all the
filter types, EqualFiltered, active Tailscale interface func, etc) and
moves the "major" change detection to net/netmon which knows more
about the world and the previous/new states.
Updates #9040
Change-Id: I7fe66a23039c6347ae5458745b709e7ebdcce245
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This makes it more maintainable for other code to statically depend
on the exact value of this string. It also makes it easier to
identify what code might depend on this string by looking up
references to this constant.
Updates tailscale/corp#13777
Signed-off-by: Joe Tsai <joetsai@digital-static.net>
This option allows logging the raw HTTP requests and responses that the
portmapper Client makes when using UPnP. This can be extremely helpful
when debugging strange UPnP issues with users' devices, and might allow
us to avoid having to instruct users to perform a packet capture.
Updates #8992
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I2c3cf6930b09717028deaff31738484cc9b008e4
I'm not saying it works, but it compiles.
Updates #5794
Change-Id: I2f3c99732e67fe57a05edb25b758d083417f083e
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
We have a fancy package for doing TLS cert validation even if the machine
doesn't have TLS certs (for LetsEncrypt only) but the CLI's netcheck command
wasn't using it.
Also, update the tlsdial's outdated package docs while here.
Updates #cleanup
Change-Id: I74b3cb645d07af4d8ae230fb39a60c809ec129ad
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This simplifies some netmon code in prep for other changes.
It breaks up Monitor.debounce into a helper method so locking is
easier to read and things unindent, and then it simplifies the polling
netmon implementation to remove the redundant stuff that the caller
(the Monitor.debounce loop) was already basically doing.
Updates #9040
Change-Id: Idcfb45201d00ae64017042a7bdee6ef86ad37a9f
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Port 0 is interpreted, per the spec (but inconsistently among router
software) as requesting to map every single available port on the UPnP
gateway to the internal IP address. We'd previously avoided picking
ports below 1024 for one of the two UPnP methods (in #7457), and this
change moves that logic so that we avoid it in all cases.
Updates #8992
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I20d652c0cd47a24aef27f75c81f78ae53cc3c71e
Make it just a views.Slice[netip.Prefix] instead of its own named type.
Having the special case led to circular dependencies in another WIP PR
of mine.
Updates #8948
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Values are still turned into pointers internally to maintain the
invariants of strideTable, but from the user's perspective it's
now possible to tbl.Insert(pfx, true) rather than
tbl.Insert(pfx, ptr.To(true)).
Updates #7781
Signed-off-by: David Anderson <danderson@tailscale.com>
In preparation for a different refactor, but incidentally also saves
10-25% memory on overall table size in benchmarks.
Updates #7781
Signed-off-by: David Anderson <danderson@tailscale.com>
Netcheck no longer performs I/O itself, instead it makes requests via
SendPacket and expects users to route reply traffic to
ReceiveSTUNPacket.
Netcheck gains a Standalone function that stands up sockets and
goroutines to implement I/O when used in a standalone fashion.
Magicsock now unconditionally routes STUN traffic to the netcheck.Client
that it hosts, and plumbs the send packet sink.
The CLI is updated to make use of the Standalone mode.
Fixes#8723
Signed-off-by: James Tucker <james@tailscale.com>
Refactor two shared functions used by the tailscale cli,
calcAdvertiseRoutes and licensesURL. These are used by the web client as
well as other tailscale subcommands. The web client is being moved out
of the cli package, so move these two functions to new locations.
Updates tailscale/corp#13775
Signed-off-by: Will Norris <will@tailscale.com>
One is a straight "I forgot how to Go" bug, the others are semantic
mismatches with the main implementation around masking the prefixes
passed to insert/delete.
Updates #7781
Signed-off-by: David Anderson <danderson@tailscale.com>
This is a prerequisite for path compression, so that insert/delete
can determine when compression occurred.
Updates #7781
Signed-off-by: David Anderson <danderson@tailscale.com>
Having `127.0.0.53` is not the only way to use `systemd-resolved`. An
alternative way is to enable `libnss_resolve` module, which seems to now
be used by default on Debian 12 bookworm.
Fixes#8549
Signed-off-by: Anton Tolchanov <anton@tailscale.com>
If the absolute value of the difference between the current
PreferredDERP's latency and the best latency is <= 10ms, don't change
it and instead prefer the previous value.
This is in addition to the existing hysteresis that tries to remain
on the previous DERP region if the relative improvement is small, but
handles nodes that have low latency to >1 DERP region better.
Updates #8603
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I1e34c94178f8c9a68a69921c5bc0227337514c70
This allows providing additional information to the client about how to
select a home DERP region, such as preferring a given DERP region over
all others.
Updates #8603
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I7c4a270f31d8585112fab5408799ffba5b75266f
When performing a fallback DNS query, run the recursive resolver in a
separate goroutine and compare the results returned by the recursive
resolver with the results we get from "regular" bootstrap DNS. This will
allow us to gather data about whether the recursive DNS resolver works
better, worse, or about the same as "regular" bootstrap DNS.
Updates #5853
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: Ifa0b0cc9eeb0dccd6f7a3d91675fe44b3b34bd48
This change introduces tstime.NewClock and tstime.ClockOpts as a new way
to construct tstime.Clock. This is a subset of #8464 as a stepping stone
so that we can update our internal code to use the new API before making
the second round of changes.
Updates #8463
Change-Id: Ib26edb60e5355802aeca83ed60e4fdf806c90e27
Signed-off-by: Adrian Dewhurst <adrian@tailscale.com>
This package contains platform-independent abstractions for fetching
information about an open TCP connection.
Updates #8413
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I236657b1060d7e6a45efc7a2f6aacf474547a2fe
This change is introducing new netfilterRunner interface and moving iptables manipulation to a lower leveled iptables runner.
For #391
Signed-off-by: KevinLiang10 <kevinliang@tailscale.com>
This commit updates our IP forwarding parsing logic to allow the less
common but still valid value of `2` to be parsed as `true`, which fixes
an error some users encountered.
Fixes#8375
Signed-off-by: Ross Zurowski <ross@rosszurowski.com>
Also fix a js/wasm issue with tsnet in the process. (same issue as WASI)
Updates #8320Fixes#8315
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
We've talked in the past about reworking how bootstrap DNS works to
instead do recursive DNS resolution from the root; this would better
support on-prem customers and Headscale users where the DERP servers
don't currently resolve their DNS server. This package is an initial
implementation of recursive resolution for A and AAAA records.
Updates #5853
Change-Id: Ibe974d78709b4b03674b47c4ef61f9a00addf8b4
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
This test was either fixed by intermediate changes or was mis-flagged as
failing during #7876 triage.
Updates #7876
Signed-off-by: James Tucker <jftucker@gmail.com>
Wait 2 minutes before we start reporting battery usage. There is always
radio activity on initial startup, which gets reported as 100% high
power usage. Let that settle before we report usage data.
Updates tailscale/corp#9230
Signed-off-by: Will Norris <will@tailscale.com>
`interfaces.Tailscale()` returns all zero values when it finds no
Tailscale interface and encounters no errors. The netns package was
treating no error as a signal that it would receive a non-zero pointer
value leading to nil pointer dereference.
Observed in:
```
--- FAIL: TestGetInterfaceIndex (0.00s)
--- FAIL: TestGetInterfaceIndex/IP_and_port (0.00s)
panic: runtime error: invalid memory address or nil pointer dereference [recovered]
panic: runtime error: invalid memory address or nil pointer dereference
[signal SIGSEGV: segmentation violation code=0x2 addr=0x0 pc=0x1029eb7d8]
goroutine 7 [running]:
testing.tRunner.func1.2({0x102a691e0, 0x102bc05c0})
/Users/raggi/.cache/tailscale-go/src/testing/testing.go:1526 +0x1c8
testing.tRunner.func1()
/Users/raggi/.cache/tailscale-go/src/testing/testing.go:1529 +0x384
panic({0x102a691e0, 0x102bc05c0})
/Users/raggi/.cache/tailscale-go/src/runtime/panic.go:884 +0x204
tailscale.com/net/netns.getInterfaceIndex(0x14000073f28, 0x1028d0284?, {0x1029ef3b7, 0xa})
/Users/raggi/src/github.com/tailscale/tailscale/net/netns/netns_darwin.go:114 +0x228
tailscale.com/net/netns.TestGetInterfaceIndex.func2(0x14000138000)
/Users/raggi/src/github.com/tailscale/tailscale/net/netns/netns_darwin_test.go:37 +0x54
testing.tRunner(0x14000138000, 0x140000551b0)
/Users/raggi/.cache/tailscale-go/src/testing/testing.go:1576 +0x10c
created by testing.(*T).Run
/Users/raggi/.cache/tailscale-go/src/testing/testing.go:1629 +0x368
FAIL tailscale.com/net/netns 0.824s
```
Fixes#8064
Signed-off-by: James Tucker <jftucker@gmail.com>
This is part of an effort to clean up tailscaled initialization between
tailscaled, tailscaled Windows service, tsnet, and the mac GUI.
Updates #8036
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
In the case where the exit node requires SNAT, we would SNAT all traffic not just the
traffic meant to go through the exit node. This was a result of the default route being
added to the routing table which would match basically everything.
In this case, we need to account for all peers in the routing table not just the ones
that require NAT.
Fix and add a test.
Updates tailscale/corp#8020
Signed-off-by: Maisem Ali <maisem@tailscale.com>
This change adds a v6conn to the pinger to enable sending pings to v6
addrs.
Updates #7826
Signed-off-by: Charlotte Brandhorst-Satzkorn <charlotte@tailscale.com>
Looks like on some systems there's an IPv6 address, but then opening
a IPv6 UDP socket fails later. Probably some firewall. Tolerate it
better and don't crash.
To repro: check the "udp6" to something like "udp7" (something that'll
fail) and run "go run ./cmd/tailscale netcheck" on a machine with
active IPv6. It used to crash and now it doesn't.
Fixes#7949
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
On some platforms (notably macOS and iOS) we look up the default
interface to bind outgoing connections to. This is both duplicated
work and results in logspam when the default interface is not available
(i.e. when a phone has no connectivity, we log an error and thus cause
more things that we will try to upload and fail).
Fixed by passing around a netmon.Monitor to more places, so that we can
use its cached interface state.
Fixes#7850
Updates #7621
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
We're using it in more and more places, and it's not really specific to
our use of Wireguard (and does more just link/interface monitoring).
Also removes the separate interface we had for it in sockstats -- it's
a small enough package (we already pull in all of its dependencies
via other paths) that it's not worth the extra complexity.
Updates #7621
Updates #7850
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
This is a follow-up to #7905 that adds two more linters and fixes the corresponding findings. As per the previous PR, this only flags things that are "obviously" wrong, and fixes the issues found.
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I8739bdb7bc4f75666a7385a7a26d56ec13741b7c
Found this when adding a test that does a ping over PeerAPI.
Our integration tests set up a trafficTrap to ensure that tailscaled
does not call out to the internet, and it does so via a HTTP_PROXY.
When adding a test for pings over PeerAPI, it triggered the trap and investigation
lead to the realization that we were not removing the Proxy when trying to
dial out to the PeerAPI.
Updates tailscale/corp#8020
Signed-off-by: Maisem Ali <maisem@tailscale.com>
Exposes some internal state of the sockstats package via the C2N and
PeerAPI endpoints, so that it can be used for debugging. For now this
includes the estimated radio on percentage and a second-by-second view
of the times the radio was active.
Also fixes another off-by-one error in the radio on percentage that
was leading to >100% values (if n seconds have passed since we started
to monitor, there may be n + 1 possible seconds where the radio could
have been on).
Updates tailscale/corp#9230
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
When splitting the radio monitor usage array, we were splitting at now %
3600 to get values into chronological order. This caused the value for
the final second to be included at the beginning of the ordered slice
rather than the end. If there was activity during that final second, an
extra five seconds of high power usage would get recorded in some cases.
This could result in a final calculation of greater than 100% usage.
This corrects that by splitting values at (now+1 % 3600).
This also simplifies the percentage calculation by always rounding
values down, which is sufficient for our usage.
Signed-off-by: Will Norris <will@tailscale.com>
It's somewhat common (e.g. when a phone has no reception), and leads to
lots of logspam.
Updates #7850
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
This adds an initial and intentionally minimal configuration for
golang-ci, fixes the issues reported, and adds a GitHub Action to check
new pull requests against this linter configuration.
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I8f38fbc315836a19a094d0d3e986758b9313f163
Exclude traffic with 100.100.100.100 (for IPv4) and
with fd7a:115c:a1e0::53 (for IPv6) since this traffic with the
Tailscale service running locally on the node.
This traffic never left the node.
It also happens to be a high volume amount of traffic since
DNS requests occur over UDP with each request coming from a
unique port, thus resulting in many discrete traffic flows.
Fixestailscale/corp#10554
Signed-off-by: Joe Tsai <joetsai@digital-static.net>
Redoes the approach from #5550 and #7539 to explicitly pass in the logf
function, instead of having global state that can be overridden.
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
This is a continuation of the earlier 2a67beaacf but more aggressive;
this now remembers that we failed to find the "home" router IP so we
don't try again later on the next call.
Updates #7621
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
So we're staying within the netip.Addr/AddrPort consistently and
avoiding allocs/conversions to the legacy net addr types.
Updates #5162
Change-Id: I59feba60d3de39f773e68292d759766bac98c917
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
We accidentally switched to ./tool/go in
4022796484 which resulted in no longer
running Windows builds, as this is attempting to run a bash script.
I was unable to quickly fix the various tests that have regressed, so
instead I've added skips referencing #7876, which we need to back and
fix.
Updates #7262
Updates #7876
Signed-off-by: James Tucker <james@tailscale.com>
To get the tree green again for other people.
Updates #7866
Change-Id: Ibdad2e1408e5f0c97e49a148bfd77aad17c2c5e5
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This also adds a bunch of tests for this function to ensure that we're
returning the proper IP(s) in all cases.
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I0d9d57170dbab5f2bf07abdf78ecd17e0e635399
This makes `omitempty` actually work, and saves bytes in each map response.
Updates tailscale/corp#8020
Signed-off-by: Maisem Ali <maisem@tailscale.com>
At the current unoptimized memory utilization of the various data structures,
100k IPv6 routes consumes in the ballpark of 3-4GiB, which risks OOMing our
386 test machine.
Until we have the optimizations to (drastically) reduce that consumption,
skip the test that bloats too much for 32-bit machines.
Signed-off-by: David Anderson <danderson@tailscale.com>
Using log.Printf may end up being printed out to the console, which
is not desirable. I noticed this when I was investigating some client
logs with `sockstats: trace "NetcheckClient" was overwritten by another`.
That turns to be harmless/expected (the netcheck client will fall back
to the DERP client in some cases, which does its own sockstats trace).
However, the log output could be visible to users if running the
`tailscale netcheck` CLI command, which would be needlessly confusing.
Updates tailscale/corp#9230
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
We use it to gate code that depends on custom Go toolchain, but it's
currently only passed in the corp runners. Add a set on OSS so that we
can catch regressions earlier.
To specifically test sockstats this required adding a build tag to
explicitly enable them -- they're normally on for iOS, macOS and Android
only, and we don't run tests on those platforms normally.
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
power state is very roughly approximated based on observed network
activity and AT&T's state transition timings for a typical 3G radio.
Updates tailscale/corp#9230
Updates #3363
Signed-off-by: Will Norris <will@tailscale.com>
This commit implements UDP offloading for Linux. GSO size is passed to
and from the kernel via socket control messages. Support is probed at
runtime.
UDP GSO is dependent on checksum offload support on the egress netdev.
UDP GSO will be disabled in the event sendmmsg() returns EIO, which is
a strong signal that the egress netdev does not support checksum
offload.
Updates tailscale/corp#8734
Signed-off-by: Jordan Whited <jordan@tailscale.com>
Noted on #5915 TS_DEBUG_MTU was not used consistently everywhere.
Extract the default into a function that can apply this centrally and
use it everywhere.
Added envknob.Lookup{Int,Uint}Sized to make it easier to keep CodeQL
happy when using converted values.
Updates #5915
Signed-off-by: James Tucker <james@tailscale.com>
When running a SOCKS or HTTP proxy, configure the tshttpproxy package to
drop those addresses from any HTTP_PROXY or HTTPS_PROXY environment
variables.
Fixes#7407
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I6cd7cad7a609c639780484bad521c7514841764b
This adds support to make exit nodes and subnet routers work
when in scenarios where NAT is required.
It also updates the NATConfig to be generated from a `wgcfg.Config` as
that handles merging prefs with the netmap, so it has the required information
about whether an exit node is already configured and whether routes are accepted.
Updates tailscale/corp#8020
Signed-off-by: Maisem Ali <maisem@tailscale.com>
This commit updates the wireguard-go dependency to pull in fixes for
the tun package, specifically 052af4a and aad7fca.
Signed-off-by: Jordan Whited <jordan@tailscale.com>
If multiple Go channels have a value (or are closed), receiving from
them all in a select will nondeterministically return one of the two
arms. In this case, it's possible that the hairpin check timer will have
expired between when we start checking and before we check at all, but
the hairpin packet has already been received. In such cases, we'd
nondeterministically set report.HairPinning.
Instead, check if we have a value in our results channel first, then
select on the value and timeout channel after. Also, add a test that
catches this particular failure.
Fixes#1795
Change-Id: I842ab0bd38d66fabc6cabf2c2c1bb9bd32febf35
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
This adds support in tstun to utitilize the SelfNodeV4MasqAddrForThisPeer and
perform the necessary modifications to the packet as it passes through tstun.
Currently this only handles ICMP, UDP and TCP traffic.
Subnet routers and Exit Nodes are also unsupported.
Updates tailscale/corp#8020
Co-authored-by: Melanie Warrick <warrick@tailscale.com>
Signed-off-by: Maisem Ali <maisem@tailscale.com>
Followup to #7518 to also export client metrics when the active interface
is cellular.
Updates tailscale/corp#9230
Updates #3363
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
