The call to appendEndpoint updates cpeer.Endpoints.
Then it is overwritten in the next line.
The only errors from appendEndpoint occur when
the host/port pair is malformed, but that cannot happen.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
It can end up executing an a new goroutine,
at which point instead of immediately stopping test execution, it hangs.
Since this is unexpected anyway, panic instead.
As a bonus, it makes call sites nicer and removes a kludge comment.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
So we have a documented & tested way to check whether we're in
netstack mode. To be used by future commits.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
For discovery when an explicit hostname/IP is known. We'll still
also send it via control for finding peers by a list.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
"Fake" doesn't mean a lot any more, given that many components
of the engine can be faked out, including in valid production
configurations like userspace-networking.
Signed-off-by: David Anderson <danderson@tailscale.com>
This makes setup more explicit in prod codepaths, without
requiring a bunch of arguments or helpers for tests and
userspace mode.
Signed-off-by: David Anderson <danderson@tailscale.com>
This works around the close syscall being slow.
We can revert this if we find a fix or if Apple makes close fast again.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
The tstun packagen contains both constructors for generic tun
Devices, and a wrapper that provides additional functionality.
Signed-off-by: David Anderson <danderson@tailscale.com>
Now callers (wgengine/monitor) don't need to mutate the state to remove
boring interfaces before calling State.Equal. Instead, the methods
to remove boring interfaces from the State are removed, as is
the reflect-using Equal method itself, and in their place is
a new EqualFiltered method that takes a func predicate to match
interfaces to compare.
And then the FilterInteresting predicate is added for use
with EqualFiltered to do the job that that wgengine/monitor
previously wanted.
Now wgengine/monitor can keep the full interface state around,
including the "boring" interfaces, which we'll need for peerapi on
macOS/iOS to bind to the interface index of the utunN device.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
e.g.
$ tailscale ping 1.1.1.1
exit node found but not enabled
$ tailscale ping 10.2.200.2
node "tsbfvlan2" found, but not using its 10.2.200.0/24 route
$ sudo tailscale up --accept-routes
$ tailscale ping 10.2.200.2
pong from tsbfvlan2 (100.124.196.94) via 10.2.200.34:41641 in 1ms
$ tailscale ping mon.ts.tailscale.com
pong from monitoring (100.88.178.64) via DERP(sfo) in 83ms
pong from monitoring (100.88.178.64) via DERP(sfo) in 21ms
pong from monitoring (100.88.178.64) via [2604:a880:4:d1::37:d001]:41641 in 22ms
This necessarily moves code up from magicsock to wgengine, so we can
look at the actual wireguard config.
Fixes#1564
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Add proto to flowtrack.Tuple.
Add types/ipproto leaf package to break a cycle.
Server-side ACL work remains.
Updates #1516
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This reverts the revert commit 84aba349d9.
And changes us to use inet.af/netstack.
Updates #1518
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Should help iOS battery life on NEProvider.wake/skip events
with useless route updates that shouldn't cause re-STUNs.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
gVisor fixed their google/gvisor#1446 so we can include gVisor mode
on 32-bit machines.
A few minor upstream API changes, as normal.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
No server support yet, but we want Tailscale 1.6 clients to be able to respond
to them when the server can do it.
Updates #1310
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
There was a logical race where Conn.Rebind could acquire the
RebindingUDPConn mutex, close the connection, fail to rebind, release
the mutex, and then because the mutex was no longer held, ReceiveIPv4
wouldn't retry reads that failed with net.ErrClosed, letting that
error back to wireguard-go, which would then stop running that receive
IP goroutine.
Instead, keep the RebindingUDPConn mutex held for the entirety of the
replacement in all cases.
Updates tailscale/corp#1289
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
interfaces.State.String tries to print a concise summary of the
network state, removing any interfaces that don't have any or any
interesting IP addresses. On macOS and iOS, for instance, there are a
ton of misc things.
But the link monitor based its are-there-changes decision on
interfaces.State.Equal, which just used reflect.DeepEqual, including
comparing all the boring interfaces. On macOS, when turning wifi on or off, there
are a ton of misc boring interface changes, resulting in hitting an earlier
check I'd added on suspicion this was happening:
[unexpected] network state changed, but stringification didn't
This fixes that by instead adding a new
interfaces.State.RemoveUninterestingInterfacesAndAddresses method that
does, uh, that. Then use that in the monitor. So then when Equal is
used later, it's DeepEqualing the already-cleaned version with only
interesting interfaces.
This makes cmd/tailscaled debug --monitor much less noisy.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Also change the type to netaddr.IP while here, because it made sorting
easier.
Updates tailscale/corp#1397
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The Engine.LinkChange method was recently removed in
e3df29d488 while misremembering how
Android's link state mechanism worked.
Rather than do some last minute rearchitecting of link state on
Android before Tailscale 1.6, restore the old Engine.LinkChange hook
for now so the Android client doesn't need any changes. But change how
it's implemented to instead inject an event into the link monitor.
Fixes#1427
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
FreeBSD tun devices don't work with the way we implement IPv6
https://github.com/tailscale/tailscale/issues/1307
At least for now, remove any IPv6 addresses from the netmap.
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
This is necessary because either protocol can be disabled globally by a
Windows registry policy, at which point trying to touch that address
family results in "Element not found" errors. This change skips programming
address families that Windows tell us are unavailable.
Fixes#1396.
Signed-off-by: David Anderson <danderson@tailscale.com>
Not great, but lets people working on new ports get going more quickly
without having to do everything up front.
As the link monitor is getting used more, I felt bad having a useless
implementation.
Updates #815
Updates #1427
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
We used to allow that, but now it just crashes.
Separately I need to figure out why it got into this path at all,
which is #1416.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Tor has a location-hidden service feature that enables users to host services
from inside the Tor network. Each of these gets a unique DNS name that ends with
.onion. As it stands now, if a misbehaving application somehow manages to make
a .onion DNS request to our DNS server, we will forward that to the DNS server,
which could leak that to malicious third parties. See the recent bug Brave had
with this[1] for more context.
RFC 7686 suggests that name resolution APIs and libraries MUST respond with
NXDOMAIN unless they can actually handle Tor lookups. We can't handle .onion
lookups, so we reject them.
[1]: https://twitter.com/albinowax/status/1362737949872431108Fixestailscale/corp#1351
Signed-off-by: Christine Dodrill <xe@tailscale.com>
Don't use os.NewFile or (*os.File).Close on the AF_ROUTE socket. It
apparently does weird things to the fd and at least doesn't seem to
close it. Just use the unix package.
The test doesn't actually fail reliably before the fix, though. It
was an attempt. But this fixes the integration tests.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Gets it out of wgengine so the Engine isn't responsible for being a
callback registration hub for it.
This also removes the Engine.LinkChange method, as it's no longer
necessary. The monitor tells us about changes; it doesn't seem to
need any help. (Currently it was only used by Swift, but as of
14dc790137 we just do the same from Go)
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
And add a --socks5-server flag.
And fix a race in SOCKS5 replies where the response header was written
concurrently with the copy from the backend.
Co-authored with Naman Sood.
Updates #707
Updates #504
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Previously tailscaled on macOS was running "/sbin/route monitor" as a
child process, but child processes aren't allowed in the Network
Extension / App Store sandbox. Instead, just do what "/sbin/route monitor"
itself does: unix.Socket(unix.AF_ROUTE, unix.SOCK_RAW, 0) and read that.
We also parse it now, but don't do anything with the parsed results yet.
We will over time, as we have with Linux netlink messages over time.
Currently any message is considered a signal to poll and see what changed.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Currently it assumes exactly 1 registered callback. This changes it to
support 0, 1, or more than 1.
This is a step towards plumbing wgengine/monitor into more places (and
moving some of wgengine's interface state fetching into monitor in a
later step)
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
UIs need to see the full unedited netmap in order to know what exit nodes they
can offer to the user.
Signed-off-by: David Anderson <danderson@tailscale.com>
* move probing out of netcheck into new net/portmapper package
* use PCP ANNOUNCE op codes for PCP discovery, rather than causing
short-lived (sub-second) side effects with a 1-second-expiring map +
delete.
* track when we heard things from the router so we can be less wasteful
in querying the router's port mapping services in the future
* use portmapper from magicsock to map a public port
Fixes#1298Fixes#1080Fixes#1001
Updates #864
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This makes cidrDiff do as much as possible before failing, and makes a
delete of an already-deleted rule be a no-op. We should never do this
ourselves, but other things on the system can, and this should help us
recover a bit.
Also adds the start of root-requiring tests.
TODO: hook into wgengine/monitor and notice when routes are changed
behind our back, and invalidate our routes map and re-read from
kernel (via the ip command) at least on the next reconfig call.
Updates tailscale/corp#1338
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Tangentially related to #987, #177, #594, #925, #505
Motivated by rebooting a launchd-controlled tailscaled and it going
into SetNetworkUp(false) mode immediately because there really is no
network up at system boot, but then it got stuck in that paused state
forever, without a monitor implementation.
When a handshake race occurs, a queued data packet can get lost.
TestTwoDevicePing expected that the very first data packet would arrive.
This caused occasional flakes.
Change TestTwoDevicePing to repeatedly re-send packets
and succeed when one of them makes it through.
This is acceptable (vs making WireGuard not drop the packets)
because this only affects communication with extremely old clients.
And those extremely old clients will eventually connect,
because the kernel will retry sends on timeout.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
We modified the standard net package to not allocate a *net.UDPAddr
during a call to (*net.UDPConn).ReadFromUDP if the caller's use
of the *net.UDPAddr does not cause it to escape.
That is https://golang.org/cl/291390.
This is the companion change to magicsock.
There are two changes required.
First, call ReadFromUDP instead of ReadFrom, if possible.
ReadFrom returns a net.Addr, which is an interface, which always allocates.
Second, reduce the lifetime of the returned *net.UDPAddr.
We do this by immediately converting it into a netaddr.IPPort.
We left the existing RebindingUDPConn.ReadFrom method in place,
as it is required to satisfy the net.PacketConn interface.
With the upstream change and both of these fixes in place,
we have removed one large allocation per packet received.
name old time/op new time/op delta
ReceiveFrom-8 16.7µs ± 5% 16.4µs ± 8% ~ (p=0.310 n=5+5)
name old alloc/op new alloc/op delta
ReceiveFrom-8 112B ± 0% 64B ± 0% -42.86% (p=0.008 n=5+5)
name old allocs/op new allocs/op delta
ReceiveFrom-8 3.00 ± 0% 2.00 ± 0% -33.33% (p=0.008 n=5+5)
Co-authored-by: Sonia Appasamy <sonia@tailscale.com>
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
addrSet maintained duplicate lists of netaddr.IPPorts and net.UDPAddrs.
Unify to use the netaddr type only.
This makes (*Conn).ReceiveIPvN a bit uglier,
but that'll be cleaned up in a subsequent commit.
This is preparatory work to remove an allocation from ReceiveIPv4.
Co-authored-by: Sonia Appasamy <sonia@tailscale.com>
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
I based my estimation of the required timeout based on locally
observed behavior. But CI machines are worse than my local machine.
16s was enough to reduce flakiness but not eliminate it. Bump it up again.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
It only affects 'go install ./...', etc, and only on darwin/arm64 (M1 Macs) where
the go-ole package doesn't compile.
No need to build it.
Updates #943
This was in place because retrieved allowed_ips was very expensive.
Upstream changed the data structure to make them cheaper to compute.
This commit is an experiment to find out whether they're now cheap enough.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
We removed the "fast retry" code from our wireguard-go fork.
As a result, pings can take longer to transit when retries are required.
Allow that.
Fixes#1277
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
The fix can make this test run unconditionally.
This moves code from 5c619882bc for
testability but doesn't fix it yet. The #1282 problem remains (when I
wrote its wake-up mechanism, I forgot there were N DERP readers
funneling into 1 UDP reader, and the code just isn't correct at all
for that case).
Also factor out some test helper code from BenchmarkReceiveFrom.
The refactoring in magicsock.go for testability should have no
behavior change.
Magicsock started dropping all traffic internally when Tailscale is
shut down, to avoid spurious wireguard logspam. This made the benchmark
not receive anything. Setting a dummy private key is sufficient to get
magicsock to pass traffic for benchmarking purposes.
Fixes#1270.
Signed-off-by: David Anderson <danderson@tailscale.com>
And move a couple other types down into leafier packages.
Now cmd/tailscale doesn't bring in netlink, magicsock, wgengine, etc.
Fixes#1181
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Unused for now, but I want to backport this commit to 1.4 so 1.6 can
start sending these and then at least 1.4 logs will stringify nicely.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Use tb.Cleanup to simplify both the API and the implementation.
One behavior change: When the number of goroutines shrinks, don't log.
I've never found these logs to be useful, and they frequently add noise.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Previously we disabled v6 support if the disable_policy knob was
missing in /proc, but some kernels support policy routing without
exposing the toggle. So instead, treat disable_policy absence as a
"maybe", and make the direct `ip -6 rule` probing a bit more
elaborate to compensate.
Fixes#1241.
Signed-off-by: David Anderson <danderson@tailscale.com>
This is mostly code movement from the wireguard-go repo.
Most of the new wgcfg package corresponds to the wireguard-go wgcfg package.
wgengine/wgcfg/device{_test}.go was device/config{_test}.go.
There were substantive but simple changes to device_test.go to remove
internal package device references.
The API of device.Config (now wgcfg.DeviceConfig) grew an error return;
we previously logged the error and threw it away.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
On Windows, configureInterface starts a goroutine reconfiguring the
Windows firewall.
But if configureInterface fails later, that goroutine kept running and
likely failing forever, spamming logs. Make it stop quietly if its
launching goroutine filed.
Rewrite log lines on the fly, based on the set of known peers.
This enables us to use upstream wireguard-go logging,
but maintain the Tailscale-style peer public key identifiers
that the rest of our systems (and people) expect.
Fixes#1183
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Also, don't try to use IPv6 LinkLocalUnicast addresses for now. Like endpoints
exchanged with control, we share them but don't yet use them.
Updates #1172
c8c493f3d9 made it always say
`created=false` which scared me when I saw it, as that would've implied
things were broken much worse. Fortunately the logging was just wrong.
DstToString is used in two places in wireguard-go: Logging and uapi.
We are switching to use uapi for wireguard-go config.
To preserve existing behavior, we need the full set of addrs.
And for logging, having the full set of addrs seems useful.
(The Addrs method itself is slated for removal. When that happens,
the implementation will move to DstToString.)
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
To save CPU and wakeups, don't run the DERP cleanup timer regularly
unless there is a non-home DERP connection open.
Also eliminates the goroutine, moving to a time.AfterFunc.
Updates #1034
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This reverts commit 08baa17d9a.
It caused deadlocks due to lock ordering violations.
It was not the right fix, and thus should simply be reverted
while we look for the right fix (if we haven't already found it
in the interim; we've fixed other logging-after-test issues).
Fixes#1161
context.cancelCtx.Done involves a mutex and isn't as cheap as I
previously assumed. Convert the donec method into a struct field and
store the channel value once. Our one magicsock.Conn gets one pointer
larger, but it cuts ~1% of the CPU time of the ReceiveFrom benchmark
and removes a bubble from the --svg output :)
This test serves two purposes:
+ check that Write() returns an error if the tstun has been
closed.
+ ensure that the close-related code in tstun is exercised in
a test case. We were getting spurious code coverage adds/drops
based on timing of when the test case finished.
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
22507adf54 stopped relying on
our fork of wireguard-go's UpdateDst callback.
As a result, we can unwind that code,
and the extra return value of ReceiveIPv{4,6}.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
TwoDevicePing is explicitly testing the behavior of the legacy codepath, everything
else is happy to assume that code no longer exists.
Signed-off-by: David Anderson <danderson@tailscale.com>
Previously, this benchmark relied on behavior of the legacy
receive codepath, which I changed in 22507adf. With this
change, the benchmark instead relies on the new active discovery
path.
Signed-off-by: David Anderson <danderson@tailscale.com>
This prevents us from continuing to do unnecessary work
(including logging) after the connection has closed.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
This adds a new IP Protocol type, TSMP on protocol number 99 for
sending inter-tailscale messages over WireGuard, currently just for
why a peer rejects TCP SYNs (ACL rejection, shields up, and in the
future: nothing listening, something listening on that port but wrong
interface, etc)
Updates #1094
Updates tailscale/corp#1185
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Commit 68ddf1 removed code that reads
`SOFTWARE\Tailscale IPN\SearchList` registry value. But the commit
left code that writes that value.
So now this package writes and never reads the value.
Remove the code to stop pointless work.
Updates #853
Signed-off-by: Alex Brainman <alex.brainman@gmail.com>
This eliminates a dependency on wgcfg.Endpoint,
as part of the effort to eliminate our wireguard-go fork.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
This makes connectivity between ancient and new tailscale nodes slightly
worse in some cases, but only in cases where the ancient version would
likely have failed to get connectivity anyway.
Signed-off-by: David Anderson <danderson@tailscale.com>
This is what every other DNS resolver I could find does, so tsdns
should do it to. This also helps avoid weird error messages about
non-existent records being unimplemented, and thus fixes#848.
Signed-off-by: Smitty <me@smitop.com>
In sendDiscoMessage there is a check of whether the connection is
closed, which is not being reliably exercised by other tests.
This shows up in code coverage reports, the lines of code in
sendDiscoMessage are alternately added and subtracted from
code coverage.
Add a test to specifically exercise and verify this code path.
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
In derpWriteChanOfAddr when we call derphttp.NewRegionClient(),
there is a check of whether the connection is already errored and
if so it returns before grabbing the lock. The lock might already
be held and would be a deadlock.
This corner case is not being reliably exercised by other tests.
This shows up in code coverage reports, the lines of code in
derpWriteChanOfAddr are alternately added and subtracted from
code coverage.
Add a test to specifically exercise this code path, and verify that
it doesn't deadlock.
This is the best tradeoff I could come up with:
+ the moment code calls Err() to check if there is an error, we
grab the lock to make sure it would deadlock if it tries to grab
the lock itself.
+ if a new call to Err() is added in this code path, only the
first one will be covered and the rest will not be tested.
+ this test doesn't verify whether code is checking for Err() in
the right place, which ideally I guess it would.
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
netaddr.IP no longer allocates, so don't need a cache or all its associated
code/complexity.
This totally removes groupcache/lru from the deps.
Also go mod tidy.
* wengine/netstack: bump gvisor to latest version
Signed-off-by: Naman Sood <naman@tailscale.com>
* update dependencies
Signed-off-by: Naman Sood <naman@tailscale.com>
* Don't change hardcoded IP
Signed-off-by: Naman Sood <naman@tailscale.com>
Not usefully functional yet (mostly a proof of concept), but getting
it submitted for some work @namansood is going to do atop this.
Updates #707
Updates #634
Updates #48
Updates #835
* show DNS name over hostname, removing domain's common MagicDNS suffix.
only show hostname if there's no DNS name.
but still show shared devices' MagicDNS FQDN.
* remove nerdy low-level details by default: endpoints, DERP relay,
public key. They're available in JSON mode still for those who need
them.
* only show endpoint or DERP relay when it's active with the goal of
making debugging easier. (so it's easier for users to understand
what's happening) The asterisks are gone.
* remove Tx/Rx numbers by default for idle peers; only show them when
there's traffic.
* include peers' owner login names
* add CLI option to not show peers (matching --self=true, --peers= also
defaults to true)
* sort by DNS/host name, not public key
* reorder columns
The log lines that wireguard-go prints as it starts
and stops its worker routines are mostly noise.
They also happen after other work is completed,
which causes failures in some of the log testing packages.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
This appears to have been the intent of the previous code,
but in practice, it only returned A records.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
To be honest I'm not fond of Golden Bytes tests like this, but
not so much as to want to rewrite the whole test. The DNS byte
format is essentially immutable at this point, the encoded bytes
aren't going to change. The rest of the test assumptions about
hostnames might, but we can fix that when it comes.
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
eccc167 introduced closeHandle which opened the handle,
but never closed it.
Windows handles should be closed.
Updates #921
Signed-off-by: Alex Brainman <alex.brainman@gmail.com>
Previously the client had heuristics to calculate which DNS search domains
to set, based on the peers' names. Unfortunately that prevented us from
doing some things we wanted to do server-side related to node sharing.
So, bump MapRequest.Version to 9 to signal that the client only uses the
explicitly configured DNS search domains and doesn't augment it with its own
list.
Updates tailscale/corp#1026
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This is a replacement for the key-related parts
of the wireguard-go wgcfg package.
This is almost a straight copy/paste from the wgcfg package.
I have slightly changed some of the exported functions and types
to avoid stutter, added and tweaked some comments,
and removed some now-unused code.
To avoid having wireguard-go depend on this new package,
wgcfg will keep its key types.
We translate into and out of those types at the last minute.
These few remaining uses will be eliminated alongside
the rest of the wgcfg package.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
The windows key timeout is longer than the wgengine watchdog timeout,
which means we never reach the timeout, instead the process exits.
Reduce the timeout so if we do hit it, at least the process continues.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
On Win10, there's a hardcoded GUID and this works.
On Win7, this GUID changes and we need to ask the tun for its
LUID and convert that from the GUID.
This commit uses the computed GUID that is placed in InterfaceName.
Diagnosed by Jason Donnenfeld. (Thanks!)
Lazy wg configuration now triggers if a peer has only endpoint
addresses (/32 for IPv4, /128 for IPv6). Subnet routers still
trigger eager configuration to avoid the need for a CIDR match
in the hot packet path.
Signed-off-by: David Anderson <danderson@tailscale.com>
The previous code used a lot of whole-function variables and shared
behavior that only triggered based on prior action from a single codepath.
Instead of that, move the small amounts of "shared" code into each switch
case.
Signed-off-by: David Anderson <danderson@tailscale.com>
Before, tailscaled would log every 10 seconds when the periodic noteRecvActivity
call happens. This is noisy, but worse it's misleading, because the message
suggests that the disco code is starting a lazy config run for a missing peer,
whereas in fact it's just an internal piece of keepalive logic.
With this change, we still log when going from 0->1 tunnel for the peer, but
not every 10s thereafter.
Signed-off-by: David Anderson <danderson@tailscale.com>
While the code was correct, I broke it during a refactoring and
tests didn't detect it. This fixes that glitch.
Signed-off-by: David Anderson <danderson@tailscale.com>
Doesn't materially affect benchmarks, but shrinks match6 by 30 instructions
and halves memory loads.
Part of #19.
Signed-off-by: David Anderson <danderson@tailscale.com>
Part of #19.
name old time/op new time/op delta
Filter/icmp4-8 32.2ns ± 3% 32.5ns ± 2% ~ (p=0.524 n=10+8)
Filter/icmp6-8 49.7ns ± 6% 43.1ns ± 4% -13.12% (p=0.000 n=9+10)
Signed-off-by: David Anderson <danderson@tailscale.com>
The packet filter still rejects all IPv6, but decodes enough from v6
packets to do something smarter in a followup.
name time/op
Decode/tcp4-8 28.8ns ± 2%
Decode/tcp6-8 20.6ns ± 1%
Decode/udp4-8 28.2ns ± 1%
Decode/udp6-8 20.0ns ± 6%
Decode/icmp4-8 21.7ns ± 2%
Decode/icmp6-8 14.1ns ± 2%
Decode/unknown-8 9.43ns ± 2%
Signed-off-by: David Anderson <danderson@tailscale.com>
In tests, we force binding to localhost to avoid OS firewall warning
dialogs.
But for IPv6, we were trying (and failing) to bind to 127.0.0.1.
You'd think we'd just say "localhost", but that's apparently ill
defined. See
https://tools.ietf.org/html/draft-ietf-dnsop-let-localhost-be-localhost
and golang/go#22826. (It's bitten me in the past, but I can't
remember specific bugs.)
So use "::1" explicitly for "udp6", which makes the test quieter.
The goal is to move some of the shenanigans we have elsewhere into the filter
package, so that all the weird things to do with poking at the filter is in
a single place, behind clean APIs.
Signed-off-by: David Anderson <danderson@tailscale.com>
We still use the packet.* alloc-free types in the data path, but
the compilation from netaddr to packet happens within the filter
package.
Signed-off-by: David Anderson <danderson@tailscale.com>
os.IsNotExist doesn't unwrap errors. errors.Is does.
The ioutil.ReadFile ones happened to be fine but I changed them so
we're consistent with the rule: if the error comes from os, you can
use os.IsNotExist, but from any other package, use errors.Is.
(errors.Is always would also work, but not worth updating all the code)
The motivation here was that we were logging about failure to migrate
legacy relay node prefs file on startup, even though the code tried
to avoid that.
See golang/go#41122
Amazingly, there doesn't seem to be a documented way of updating network
configuration programmatically in a way that Windows takes notice of.
The naturopathic remedy for this is to invoke ipconfig /registerdns, which
does a variety of harmless things and also invokes the private API that
tells windows to notice new adapter settings. This makes our DNS config
changes stick within a few seconds of us setting them.
If we're invoking a shell command anyway, why futz with the registry at
all? Because netsh has no command for changing the DNS suffix list, and
its commands for setting resolvers requires parsing its output and
keeping track of which server is in what index. Amazingly, twiddling
the registry directly is the less painful option.
Fixes#853.
Signed-off-by: David Anderson <danderson@tailscale.com>
Updating the Windows firewall is usually reasonably fast, but
sometimes blocks for 20 seconds, 4 minutes, etc. Not sure why.
Until we understand that's happening, configure it in the background
without blocking the normal control flow.
Updates #785
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The RusagePrefixLog is rarely useful, hasn't been useful in a long
time, is rarely the measurement we need, and is pretty spammy (and
syscall-heavy). Disable it by default. We can enable it when we're
debugging memory.
At startup the client doesn't yet have the DERP map so can't do STUN
queries against DERP servers, so it only knows it local interface
addresses, not its STUN-mapped addresses.
We were reporting the interface-local addresses to control, getting
the DERP map, and then immediately reporting the full set of
updates. That was an extra HTTP request to control, but worse: it was
an extra broadcast from control out to all the peers in the network.
Now, skip the initial update if there are no stun results and we don't
have a DERP map.
More work remains optimizing start-up requests/map updates, but this
is a start.
Updates tailscale/corp#557
There was a bug with the lazy wireguard config code where, if the
minimum set of peers to tell wireguard didn't change, we skipped
calling userspaceEngine.updateActivityMapsLocked which updated
the various data structures that matched incoming traffic to later
reconfigure the minimum config.
That meant if an idle peer restarted and changed discovery keys, we
skipped updating our maps of disco keys/IPs that would caused us to
lazily inflate the config for that peer later if/when it did send
traffic.
Use golang.zx2c4.com/wireguard/windows/tunnel/winipcfg
instead of github.com/tailscale/winipcfg-go package.
Updates #760
Signed-off-by: Alex Brainman <alex.brainman@gmail.com>
Due to a copy/paste-o, we were monitoring address changes twice, and
not monitoring route changes at all.
Verified with 'tailscale debug --monitor' that this actually works now (while
running 'route add 10.3.0.0 mask 255.255.0.0 10.0.0.1' and 'route delete (same)'
back and forth in cmd.exe)
In practice route changes are accompanied by address changes and this
doesn't fix any known issues. I just noticed this while reading this
code again. But at least the code does what it was trying to do now.
This function is only called in fake mode, which won't do anything more
with the packet after we respond to it anyway, so dropping it in the
prefilter is not necessary. And it's kinda semantically wrong: we did
not reject it, so telling the upper layer that it was rejected produces
an ugly error message.
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
At some point faketun got implemented as a loopback (put a packet in
from wireguard, the same packet goes back to wireguard) which is not
useful. It's supposed to be an interface that just sinks all packets,
and then wgengine adds *only* and ICMP Echo responder as a layer on
top.
This caused extremely odd bugs on darwin, where the special case that
reinjects packets from local->local was filling the loopback channel
and creating an infinite loop (which became jammed since the reader and
writer were in the same goroutine).
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
If no interfaces are up, calm down and stop spamming so much. It was
noticed as especially bad on Windows, but probably was bad
everywhere. I just have the best network conditions testing on a
Windows VM.
Updates #604
Gracefully skips touching the v6 NAT table on systems that don't have
it, and doesn't configure IPv6 at all if IPv6 is globally disabled.
Signed-off-by: David Anderson <danderson@tailscale.com>
When the network link changes, existing UDP sockets fail immediately
and permanently on macOS.
The forwarder set up a single UDP conn and never changed it.
As a result, any time there was a network link change,
all forwarded DNS queries failed.
To fix this, create a new connection when send requests
fail because of network unreachability.
This change is darwin-only, although extended it to other platforms
should be straightforward.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
While we're here, parseQuery into a plain function.
This is helpful for fuzzing. (Which I did a bit of. Didn't find anything.)
And clean up a few minor things.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Part of unforking our winipcfg-go and using upstream (#760), move our
additions into our repo. (We might upstream them later if upstream has
interest)
Originally these were:
@apenwarr: "Add ifc.SyncAddresses() and SyncRoutes()."
609dcf2df5
@bradfitz: "winipcfg: make Interface.AddRoutes do as much as possible, return combined error"
e9f93d53f3
@bradfitz: "prevent unnecessary Interface.SyncAddresses work; normalize IPNets in deltaNets"
decb9ee8e1
Might fix it. I've spent too much time failing to reproduce the issue. This doesn't
seem to make it worse, though (it still runs for me), so I'll include this and
see if it helps others while I still work on a reliable way to reproduce it.
Updates tailscale/corp#474
Otherwise when PAC server is down, we log, and each log entry is a new
HTTP request (from logtail) and a new GetProxyForURL call, which again
logs, non-stop. This is also nicer to the WinHTTP service.
Then also hook up link change notifications to the cache to reset it
if there's a chance the network might work sooner.
This change is to restore /etc/resolv.conf after tailscale down is called. This is done by setting the dns.Manager before errors occur. Error collection is also added.
Fixes#723
* wgengine/router/router_linux.go: Switched `cidrDiff("addr")` and `cidrDiff("route")` order
Signed-off-by: Christina Wen <christina@tailscale.com>
Co-authored-by: Christina Wen <christina@tailscale.com>
Also remove rebinding logic from the windows router. Magicsock will
instead rebind based on link change signals.
Signed-off-by: David Anderson <danderson@tailscale.com>
Updates #654. See that issue for a discussion of why
this timeout reduces flakiness, and what next steps are.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
For now. Get it working again so it's not stuck on 0.98.
Subnet relay can come later.
Updates #451
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Start of making the IPN state machine react to link changes and down
its DNS & routes if necessary to unblock proxy resolution (e.g. for
transitioning from public to corp networks where the corp network has
mandatory proxies and WPAD PAC files that can't be resolved while
using the DNS/routes configured previously)
This change should be a no-op. Just some callback plumbing.
It turns out that otherwise we don't know what exactly was set.
Also remove the now unused RootDomain config option.
Signed-off-by: Dmytro Shynkevych <dmytro@tailscale.com>
Previously, a type AAAA query would be answered with an A record
if only an IPv4 address was available. This is irrelevant for us
while we only use IPv4, but it will be a bug one day,
so it's worth being precise about semantics.
Signed-off-by: Dmytro Shynkevych <dmytro@tailscale.com>
Rather than consider bigs jumps in last-received-from activity as a
signal to possibly reconfigure the set of wireguard peers to have
configured, instead just track the set of peers that are currently
excluded from the configuration. Easier to reason about.
Also adds a bit more logging.
This might fix an error we saw on a machine running a recent unstable
build:
2020-08-26 17:54:11.528033751 +0000 UTC: 8.6M/92.6M magicsock: [unexpected] lazy endpoint not created for [UcppE], d:42a770f678357249
2020-08-26 17:54:13.691305296 +0000 UTC: 8.7M/92.6M magicsock: DERP packet received from idle peer [UcppE]; created=false
2020-08-26 17:54:13.691383687 +0000 UTC: 8.7M/92.6M magicsock: DERP packet from unknown key: [UcppE]
If it does happen again, though, we'll have more logs.
Seems to break linux CI builder. Cannot reproduce locally,
so attempting a rollback.
This reverts commit cd7bc02ab1.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
Without this, a freshly started ipn client will be stuck in the
"Starting" state until something triggers a call to RequestStatus.
Usually a UI does this, but until then we can sit in this state
until poked by an external event, as is evidenced by our e2e tests
locking up when DERP is attached.
(This only recently became a problem when we enabled lazy handshaking
everywhere, otherwise the wireugard tunnel creation would also
trigger a RequestStatus.)
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
The previous approach modifies name in-place in the request slice to avoid an allocation.
This is incorrect: the question section of a DNS request
must be copied verbatim, without any such modification.
Software may rely on it (we rely on other resolvers doing it it in tsdns/forwarder).
Signed-off-by: Dmytro Shynkevych <dmytro@tailscale.com>
control/controlclient, wgengine/filter: extract parsePacketFilter to new constructor in wgengine/filter
Signed-off-by: chungdaniel <daniel@tailscale.com>
Consider:
Hard NAT (A) <---> Hard NAT w/ mapped port (B)
If A sends a packet to B's mapped port, A can disco ping B directly,
with low latency, without DERP.
But B couldn't establish a path back to A and needed to use DERP,
despite already logging about A's endpoint and adding a mapping to it
for other purposes (the wireguard conn.Endpoint lookup also needed
it).
This adds the tracking to discoEndpoint too so it'll be used for
finding a path back.
Fixestailscale/corp#556
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
For example:
$ tailscale ping -h
USAGE
ping <hostname-or-IP>
FLAGS
-c 10 max number of pings to send
-stop-once-direct true stop once a direct path is established
-verbose false verbose output
$ tailscale ping mon.ts.tailscale.com
pong from monitoring (100.88.178.64) via DERP(sfo) in 65ms
pong from monitoring (100.88.178.64) via DERP(sfo) in 252ms
pong from monitoring (100.88.178.64) via [2604:a880:2:d1::36:d001]:41641 in 33ms
Fixes#661
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
1) we weren't waking up a discoEndpoint that once existed and
went idle for 5 minutes and then got a disco message again.
2) userspaceEngine.noteReceiveActivity had a buggy check; fixed
and added a test
This removes the atomic bool that tried to track whether we needed to acquire
the lock on a future recursive call back into magicsock. Unfortunately that
hack doesn't work because we also had a lock ordering issue between magicsock
and userspaceEngine (see issue). This documents that too.
Fixes#644
If a node is behind a hard NAT and is using an explicit local port
number, assume they might've mapped a port and add their public IPv4
address with the local tailscaled's port number as a candidate endpoint.
A comparison operator was backwards.
The bad case went:
* device A send packet to B at t=1s
* B gets added to A's wireguard config
* B gets packet
(5 minutes pass)
* some other activity happens, causing B to expire
to be removed from A's network map, since it's
been over 5 minutes since sent or received activity
* device A sends packet to B at t=5m1s
* normally, B would get added back, but the old send
time was not zero (we sent earlier!) and the time
comparison was backwards, so we never regenerated
the wireguard config.
This also refactors the code for legibility and moves constants up
top, with comments.
The OS (tries) to send these but we drop them. No need to worry the
user with spam that we're dropping it.
Fixes#402
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Starting with fe68841dc7, some e2e tests
got flaky. Rather than debug them (they're gnarly), just revert to the old
behavior as far as those tests are concerned. The tests were somehow
using magicsock without a private key and expecting it to do ... something.
My goal with fe68841dc7 was to stop log spam
and unnecessary work I saw on the iOS app when when stopping the app.
Instead, only stop doing that work on any transition from
once-had-a-private-key to no-longer-have-a-private-key. That fixes
what I wanted to fix while still making the mysterious e2e tests
happy.
There is a race in natlab where we might start shutdown while natlab is still running
a goroutine or two to deliver packets. This adds a small grace period to try and receive
it before continuing shutdown.
Signed-off-by: David Anderson <danderson@tailscale.com>
The first packet to transit may take several seconds to do so, because
setup rates in wgengine may result in the initial WireGuard handshake
init to get dropped. So, we have to wait at least long enough for a
retransmit to correct the fault.
Signed-off-by: David Anderson <danderson@tailscale.com>
Active discovery lets us introspect the state of the network stack precisely
enough that it's unnecessary, and dropping the initial DERP packets greatly
slows down tests. Additionally, it's unrealistic since our production network
will never deliver _only_ discovery packets, it'll be all or nothing.
Signed-off-by: David Anderson <danderson@tailscale.com>
Uses natlab only, because the point of this active discovery test is going to be
that it should get through a lot of obstacles.
Signed-off-by: David Anderson <danderson@tailscale.com>
The deadlock was:
* Conn.Close was called, which acquired c.mu
* Then this goroutine scheduled:
if firstDerp {
startGate = c.derpStarted
go func() {
dc.Connect(ctx)
close(c.derpStarted)
}()
}
* The getRegion hook for that derphttp.Client then ran, which also
tries to acquire c.mu.
This change makes that hook first see if we're already in a closing
state and then it can pretend that region doesn't exist.
wireguard-go uses 3 goroutines per peer (with reasonably large stacks
& buffers).
Rather than tell wireguard-go about all our peers, only tell it about
peers we're actively communicating with. That means we need hooks into
magicsock's packet receiving path and tstun's packet sending path to
lazily create a wireguard peer on demand from the network map.
This frees up lots of memory for iOS (where we have almost nothing
left for larger domains with many users).
We should ideally do this in wireguard-go itself one day, but that'd
be a pretty big change.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
sync.Pools should almost always be packate globals, even though in this
case we only have exactly 1 TUN device anyway, so it matters less.
Still, it's unusual to see a Pool that's not a package global, so move it.
We originally picked those numbers somewhat at random, but with the idea
that 8 is a traditionally lucky number in Chinese culture. Unfortunately,
"88" is also neo-nazi shorthand language.
Use 52 instead, because those are the digits above the letters
"TS" (tailscale) on a qwerty keyboard, so we're unlikely to collide with
other users. 5, 2 and 52 are also pleasantly culturally meaningless.
Signed-off-by: David Anderson <danderson@tailscale.com>
Nameserver IP 10.11.12.13 would otherwise get written to resolv.conf as 13.12.11.10, as was happening on my client.
Signed-off-by: Eduardo Kienetz <eduardo@kienetz.com>
Before this patch, the 250ms sleep would not be interrupted by context cancellation,
which would result in the goroutine sometimes lingering in tests (100ms grace period).
Signed-off-by: Dmytro Shynkevych <dmytro@tailscale.com>
Very rarely, cancellation occurs between a successful send on derpRecvCh
and a call to copyBuf on the receiving side.
Without this patch, this situation results in <-copyBuf blocking indefinitely.
Signed-off-by: Dmytro Shynkevych <dmytro@tailscale.com>
Peers advertising a discovery key know how to speak the discovery
protocol and do their own heartbeats to get through NATs and keep NATs
open. No need for the pinger except for with legacy peers.
The new interface lets implementors more precisely distinguish
local traffic from forwarded traffic, and applies different
forwarding logic within Machines for each type. This allows
Machines to be packet forwarders, which didn't quite work
with the implementation of Inject.
Signed-off-by: David Anderson <danderson@tailscale.com>
This log line looks buggy, even though lacking a filter is expected during bringup.
We already know if we forget to SetFilter: it breaks the magicsock test,
so no useful information is lost.
Resolves#559.
Signed-off-by: Dmytro Shynkevych <dmytro@tailscale.com>
The test demonstrates that magicsock can traverse two stateful
firewalls facing each other, that each require localhost to
initiate connections.
Signed-off-by: David Anderson <danderson@tailscale.com>
This change adds to tsdns the ability to delegate lookups to upstream nameservers.
This is crucial for setting Magic DNS as the system resolver.
Signed-off-by: Dmytro Shynkevych <dmytro@tailscale.com>
Never return "nil, nil" anymore. The caller expected a usable
interface now. I missed some of these earlier.
Also, handle address deletion now.
Updates #532
There's a lot of confusion around what tailscale status shows, so make it better:
show region names, last write time, and put stars around DERP too if active.
Now stars are always present if activity, and always somewhere.
* fix tailscale status for peers using discovery
* as part of that, pull out disco address selection into reusable
and testable discoEndpoint.addrForSendLocked
* truncate ping/pong logged hex txids in half to eliminate noise
* move a bunch of random time constants into named constants
with docs
* track a history of per-endpoint pong replies for future use &
status display
* add "send" and " got" prefix to discovery message logging
immediately before the frame type so it's easier to read than
searching for the "<-" or "->" arrows earlier in the line; but keep
those as the more reasily machine readable part for later.
Updates #483
Update the mapping from ip:port to discokey, so when we retrieve a
packet from the network, we can find the same conn.Endpoint that we
gave to wireguard-go previously, without making it think we've
roamed. (We did, but we're not using its roaming.)
Updates #483
Ping messages now go out somewhat regularly, pong replies are sent,
and pong replies are now partially handled enough to upgrade off DERP
to LAN.
CallMeMaybe packets are sent & received over DERP, but aren't yet
handled. That's next (and regular maintenance timers), and then WAN
should work.
Updates #483
Starting at yesterday's e96f22e560 (convering some UDPAddrs to
IPPorts), Conn.ReceiveIPv4 could return a nil addr, which would make
its way through wireguard-go and blow up later. The DERP read path
wasn't initializing the addr result parameter any more, and wgRecvAddr
wasn't checking it either.
Fixes#515
And while plumbing, a bit of discovery work I'll need: the
endpointOfAddr map to map from validated paths to the discoEndpoint.
Not being populated yet.
Updates #483
This adds a new magicsock endpoint type only used when both sides
support discovery (that is, are advertising a discovery
key). Otherwise the old code is used.
So far the new code only communicates over DERP as proof that the new
code paths are wired up. None of the actually discovery messaging is
implemented yet.
Support for discovery (generating and advertising a key) are still
behind an environment variable for now.
Updates #483
The new deepprint package just walks a Go data structure and writes to
an io.Writer. It's not pretty like go-spew, etc.
We then use it to replace the use of UAPI (which we have a TODO to
remove) to generate signatures of data structures to detect whether
anything changed (without retaining the old copy).
This was necessary because the UAPI conversion ends up trying to do
DNS lookups which an upcoming change depends on not happening.
And track known peers.
Doesn't yet do anything with the messages. (nor does it send any yet)
Start of docs on the message format. More will come in subsequent changes.
Updates #483
The NetworkExtension brings up the interface itself and does not have
access to `ifconfig`, which the underlying BSD userspace router attempts
to use when Up is called.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
If there's been 5 minutes of inactivity, stop doing STUN lookups. That
means NAT mappings will expire, but they can resume later when there's
activity again.
We'll do this for all platforms later.
Updates tailscale/corp#320
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Darwin and FreeBSD are compatible enough to share the userspace router.
The OSX router delegates to the BSD userspace router unless `SetRoutesFunc` is set.
That preserves the mechanism that allows `ipn-go-bridge` to specify its own routing behavior.
Fixes#177
Signed-off-by: Reinaldo de Souza <github@rei.nal.do>
The magicsock derpReader was holding onto 65KB for each DERP
connection forever, just in case.
Make the derp{,http}.Client be in charge of memory instead. It can
reuse its bufio.Reader buffer space.
macOS incorrectly sends packets for the local Tailscale IP
into our tunnel interface. We have to turn the packets around
and send them back to the kernel.
Fixestailscale/corp#189.
Signed-off-by: David Anderson <danderson@tailscale.com>
iproute2 3.16.0-2 from Debian Jessie (oldoldstable) doesn't return
exit code 2 when deleting a non-existent IP rule.
Fixes#434
Signed-off-by: David Anderson <danderson@tailscale.com>
We have a filter in tailscaled itself now, which is more robust
against weird network topologies (such as the one Docker creates).
Signed-off-by: David Anderson <danderson@tailscale.com>
We'll use SO_BINDTODEVICE instead of fancy policy routing. This has
some limitations: for example, we will route all traffic through the
interface that has the main "default" (0.0.0.0/0) route, so machines
that have multiple physical interfaces might have to go through DERP to
get to some peers. But machines with multiple physical interfaces are
very likely to have policy routing (ip rule) support anyway.
So far, the only OS I know of that needs this feature is ChromeOS
(crostini). Fixes#245.
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
Otherwise iOS/macOS will reconfigure their routing every time anything
minor changes in the netmap (in particular, endpoints and DERP homes),
which is way too often.
Some users reported "network reconfigured" errors from Chrome when this
happens.
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
This allows tailscaled's own traffic to bypass Tailscale-managed routes,
so that things like tailscale-provided default routes don't break
tailscaled itself.
Progress on #144.
Signed-off-by: David Anderson <danderson@tailscale.com>
We canceled the pingers in Close, but didn't wait around for their
goroutines to be cleaned up. This caused the ipn/e2e_test to catch
pingers in its resource leak check.
This commit introduces an object, but also simplifies the semantics
around the pinger's cancel functions. They no longer need to be called
while holding the mutex.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
Specifically, this sequence:
iptables -N ts-forward
iptables -A ts-forward -m mark --mark 0x10000 -j ACCEPT
iptables -A FORWARD -j ts-forward
doesn't work on Debian-9-using-nftables, but this sequence:
iptables -N ts-forward
iptables -A FORWARD -j ts-forward
iptables -A ts-forward -m mark --mark 0x10000 -j ACCEPT
does work.
I'm sure the reason why is totally fascinating, but it's an old version
of iptables and the bug doesn't seem to exist on modern nftables, so
let's refactor our code to add rules in the always-safe order and
pretend this never happened.
Fixes#401.
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
On startup, and when switching into =off and =nodivert, we were
deleting netfilter rules even if we weren't the ones that added them.
In order to avoid interfering with rules added by the sysadmin, we have
to be sure to delete rules only in the case that we added them in the
first place.
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
Instead of retrieving the list of chains, or the list of rules in a
chain, just try deleting the ones we don't want and then adding the
ones we do want. An error in flushing/deleting still means the rule
doesn't exist anymore, so there was no need to check for it first.
This avoids the need to parse iptables output, which avoids the need to
ever call iptables -S, which fixes#403, among other things. It's also
much more future proof in case the iptables command line changes.
Unfortunately the iptables go module doesn't properly pass the iptables
command exit code back up when doing .Delete(), so we can't correctly
check the exit code there. (exit code 1 really means the rule didn't
exist, rather than some other weird problem).
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
This removes the use of suppress_ifgroup and fwmark "x/y" notation,
which are, among other things, not available in busybox and centos6.
We also use the return codes from the 'ip' program instead of trying to
parse its output.
I also had to remove the previous hack that routed all of 100.64.0.0/10
by default, because that would add the /10 route into the 'main' route
table instead of the new table 88, which is no good. It was a terrible
hack anyway; if we wanted to capture that route, we should have
captured it explicitly as a subnet route, not as part of the addr. Note
however that this change affects all platforms, so hopefully there
won't be any surprises elsewhere.
Fixes#405
Updates #320, #144
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
Instead of hard-coding the DERP map (except for cmd/tailscale netcheck
for now), get it from the control server at runtime.
And make the DERP map support multiple nodes per region with clients
picking the first one that's available. (The server will balance the
order presented to clients for load balancing)
This deletes the stunner package, merging it into the netcheck package
instead, to minimize all the config hooks that would've been
required.
Also fix some test flakes & races.
Fixes#387 (Don't hard-code the DERP map)
Updates #388 (Add DERP region support)
Fixes#399 (wgengine: flaky tests)
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The comment module is compiled out on several embedded systems (and
also gentoo, because netfilter can't go brrrr with comments holding it
back). Attempting to use comments results in a confusing error, and a
non-functional firewall.
Additionally, make the legacy rule cleanup non-fatal, because we *do*
have to probe for the existence of these -m comment rules, and doing
so will error out on these systems.
Signed-off-by: David Anderson <danderson@tailscale.com>
Our new build scripts try to build ipn-go-bridge on more than just
linux and darwin, so let's enable this file so it can be successful on
every platform.
This didn't catch anything yet, but it's good practice for detecting
goroutine leaks that we might not find otherwise.
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
If a test calls log.Printf, 'go test' horrifyingly rearranges the
output to no longer be in chronological order, which makes debugging
virtually impossible. Let's stop that from happening by making
log.Printf panic if called from any module, no matter how deep, during
tests.
This required us to change the default error handler in at least one
http.Server, as well as plumbing a bunch of logf functions around,
especially in magicsock and wgengine, but also in logtail and backoff.
To add insult to injury, 'go test' also rearranges the output when a
parent test has multiple sub-tests (all the sub-test's t.Logf is always
printed after all the parent tests t.Logf), so we need to screw around
with a special Logf that can point at the "current" t (current_t.Logf)
in some places. Probably our entire way of using subtests is wrong,
since 'go test' would probably like to run them all in parallel if you
called t.Parallel(), but it definitely can't because the're all
manipulating the shared state created by the parent test. They should
probably all be separate toplevel tests instead, with common
setup/teardown logic. But that's a job for another time.
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
Right now, filtering and packet injection in wgengine depend
on a patch to wireguard-go that probably isn't suitable for upstreaming.
This need not be the case: wireguard-go/tun.Device is an interface.
For example, faketun.go implements it to mock a TUN device for testing.
This patch implements the same interface to provide filtering
and packet injection at the tunnel device level,
at which point the wireguard-go patch should no longer be necessary.
This patch has the following performance impact on i7-7500U @ 2.70GHz,
tested in the following namespace configuration:
┌────────────────┐ ┌─────────────────────────────────┐ ┌────────────────┐
│ $ns1 │ │ $ns0 │ │ $ns2 │
│ client0 │ │ tailcontrol, logcatcher │ │ client1 │
│ ┌─────┐ │ │ ┌──────┐ ┌──────┐ │ │ ┌─────┐ │
│ │vethc│───────┼────┼──│vethrc│ │vethrs│──────┼─────┼──│veths│ │
│ ├─────┴─────┐ │ │ ├──────┴────┐ ├──────┴────┐ │ │ ├─────┴─────┐ │
│ │10.0.0.2/24│ │ │ │10.0.0.1/24│ │10.0.1.1/24│ │ │ │10.0.1.2/24│ │
│ └───────────┘ │ │ └───────────┘ └───────────┘ │ │ └───────────┘ │
└────────────────┘ └─────────────────────────────────┘ └────────────────┘
Before:
---------------------------------------------------
| TCP send | UDP send |
|------------------------|------------------------|
| 557.0 (±8.5) Mbits/sec | 3.03 (±0.02) Gbits/sec |
---------------------------------------------------
After:
---------------------------------------------------
| TCP send | UDP send |
|------------------------|------------------------|
| 544.8 (±1.6) Mbits/sec | 3.13 (±0.02) Gbits/sec |
---------------------------------------------------
The impact on receive performance is similar.
Signed-off-by: Dmytro Shynkevych <dmytro@tailscale.com>
This saves a layer of translation, and saves us having to
pass in extra bits and pieces of the netmap and prefs to
wgengine. Now it gets one Wireguard config, and one OS
network stack config.
Signed-off-by: David Anderson <danderson@tailscale.com>
Defensive programming against #368 in environments other than Docker,
e.g. if you try using Tailscale in Alpine Linux directly, sans
container.
Signed-off-by: David Anderson <danderson@tailscale.com>
The iptables package we use doesn't include command output, so we're
left with guessing what went wrong most of the time. This will at
least narrow things down to which operation failed.
Signed-off-by: David Anderson <danderson@tailscale.com>
Instead, pass in only exactly the relevant configuration pieces
that the OS network stack cares about.
Signed-off-by: David Anderson <danderson@tailscale.com>
New logic installs precise filters for subnet routes,
plays nice with other users of netfilter, and lays the
groundwork for fixing routing loops via policy routing.
Signed-off-by: David Anderson <danderson@tailscale.com>
This depends on improved support from the control server, to send the
new subnet width (Bits) fields. If these are missing, we fall back to
assuming their value is /32.
Conversely, if the server sends Bits fields to an older client, it will
interpret them as /32 addresses. Since the only rules we allow are
"accept" rules, this will be narrower or equal to the intended rule, so
older clients will simply reject hosts on the wider subnet (fail
closed).
With this change, the internal filter.Matches format has diverged
from the wire format used by controlclient, so move the wire format
into tailcfg and convert it to filter.Matches in controlclient.
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
Longer term, we should probably update the packet filter to be fully
stateful, for both TCP and ICMP. That is, only ICMP packets related to
a session *we* initiated should be allowed back in. But this is
reasonably secure for now, since wireguard is already trimming most
traffic. The current code would not protect against eg. Ping-of-Death style
attacks from VPN nodes.
Fixestailscale/tailscale#290.
Signed-off-by: Avery Pennarun <apenwarr@tailscale.com>
This was only done occasionally, but was extremely disruptive
when done and is no longer necessary.
It used to be that when switching links, we had to immediately
generate handshakes to everyone we were communicating with to
punch a hole in any NAT we were talking through. (This ended up
not really working, because in the process we got rid of our
session keys and ended up having a futile conversation for many
seconds.)
Now we have DERP, our link change propogates to the other side
as a new list of endpoints, so they start spraying packets.
We will definitely get one thanks to DERP, which will cause us
to spray, opening any NAT we are behind.
The result is that for good connections, we don't trash session
keys and cause an interruption.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
It was one of the top garbage producers on my phone.
It's slated to be deleted and replaced anyway, but this helps in the
meantime.
The go.sum changes look scary, but the new dep only adds 240 bytes to
the binary. The go.sum noise is just cmd/go being aggressive in
including a lot of stuff (which is being fixed in Go 1.15, for what I
understand). And I ran a go mod tidy, which added some too. (I had to
write a custom wrapper around go mod tidy because this mod tidy
normally breaks on tailscale.io/control being missing but referenced
in tests)
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The docs on magicsock.Conn stated that they implemented the
wireguard/device.Bind interface, yet this type does not exist. In
reality, the Conn type implements the wireguard/conn.Bind interface.
I also fixed a small typo in the same file.
Signed-off-by: Blake Gentry <blakesgentry@gmail.com>
* remove endpoint discovery noise when results unchanged
* consistently spell derp nodes as "derp-N"
* replace "127.3.3.40:" with "derp-" in CreateEndpoint log output
* stop early DERP setup before SetPrivateKey is called;
it just generates log nosie
* fix stringification of peer ShortStrings (it had an old %x on it,
rendering it garbage)
* describe why derp routes are changing, with one of:
shared home, their home, our home, alt
Add opt-in method to request IPv6 endpoints from the control plane.
For now they should just be skipped. A previous version of this CL was
unconditional and reportedly had problems that I can't reproduce. So
make it a knob until the mystery is solved.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Breaks something deep in wireguard or magicsock's brainstem, no packets at all
can flow. All received packets fail decryption with "invalid mac1".
This reverts commit 94024355ed.
Signed-off-by: David Anderson <dave@natulte.net>
More steps towards IPv6 transport.
We now send it to tailcontrol, which ignores it.
But it doesn't actually actually support IPv6 yet (outside of STUN).
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Use this when making the ipn state transition from Starting to
Running. This way a network of quiet nodes with no active
handshaking will still transition to Active.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
Typically the home DERP server is found and set on startup before
magicsock's SetPrivateKey can be called, so no DERP connection is
established. Make sure one is by kicking the home DERP tires in
SetPrivateKey.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
The code as written intended to do this, but it repeated the
comparison of derpNum and c.myDerp after c.myDerp had been
updated, so it never executed.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
Before, endpoint updates were constantly being interrupted and resumed
on Linux due to tons of LinkChange messages from over-zealous Linux
netlink messages (from router_linux.go)
Now that endpoint updates are fast and bounded in time anyway, just
let them run to completion, but note that another needs to be
scheduled after.
Now logs went from pages of noise to just:
root@taildoc:~# grep -i -E 'stun|endpoint update' log
2020/03/13 08:51:29 magicsock.Conn: starting endpoint update (initial)
2020/03/13 08:51:30 magicsock.Conn.ReSTUN: endpoint update active, need another later ("link-change-minor")
2020/03/13 08:51:31 magicsock.Conn: starting endpoint update (link-change-minor)
2020/03/13 08:51:31 magicsock.Conn.ReSTUN: endpoint update active, need another later ("link-change-minor")
2020/03/13 08:51:33 magicsock.Conn: starting endpoint update (link-change-minor)
2020/03/13 08:51:33 magicsock.Conn.ReSTUN: endpoint update active, need another later ("link-change-minor")
2020/03/13 08:51:35 magicsock.Conn: starting endpoint update (link-change-minor)
2020/03/13 08:51:35 magicsock.Conn.ReSTUN: endpoint update active, need another later ("link-change-minor")
Or, seen in another run:
2020/03/13 08:45:41 magicsock.Conn: starting endpoint update (periodic)
2020/03/13 08:46:09 magicsock.Conn: starting endpoint update (periodic)
2020/03/13 08:46:21 magicsock.Conn: starting endpoint update (link-change-major)
2020/03/13 08:46:37 magicsock.Conn: starting endpoint update (periodic)
2020/03/13 08:47:05 magicsock.Conn: starting endpoint update (periodic)
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The TODO above derphttp.NewClient suggests it does network I/O,
but the derphttp client connects lazily and so creating one is
very cheap.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
It used to make assumptions based on having Anycast IPs that are super
near. Now we're intentionally going to a bunch of different distant
IPs to measure latency.
Also, optimize how the hairpin detection works. No need to STUN on
that socket. Just use that separate socket for sending, once we know
the other UDP4 socket's endpoint. The trick is: make our test probe
also a STUN packet, so it fits through magicsock's existing STUN
routing.
This drops netcheck from ~5 seconds to ~250-500ms.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Failure to do this leads to fd exhaustion at -count=10000,
and increasingly poor execution north of -count=100.
Signed-off-by: David Anderson <danderson@tailscale.com>
Failure to do so triggers either a data race or a panic
in the testing package, due to racey use of t.Logf.
Signed-off-by: David Anderson <danderson@tailscale.com>
Basically, don't trust the OS-level link monitor to only tell you
interesting things. Sanity check it.
Also, move the interfaces package into the net directory now that we
have it.
This was (presumably) missing from wgengine because the
interactions between magicsock and wireguard-go meant that the
shutdown never worked. Now those are fixed, actually shut down.
Fixes occasional flake in expanded ipn/e2e_test.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
The device name "tailscale0" will be used for all platforms except for
OpenBSD where "tun" is enforced by the kernel. `CreateTUN()` in
`wireguard-go` will select the next available "tunX" device name on the
OpenBSD system.
Signed-off-by: Martin Baillie <martin@baillie.email>
The UDP reader goroutine was clobbering `n` and `err` from the
main goroutine, whose accesses are not synchronized the way `b` is.
Signed-off-by: David Anderson <danderson@tailscale.com>
wireguard-go closes magicsock, and expects this to unblock reads
so that its internal goroutines can wind down. We were incorrectly
blocking the read indefinitey and breaking this contract.
Signed-off-by: David Anderson <danderson@tailscale.com>
It's extremely flaky in several dimensions, as well as very slow.
It's making the CI completely red all the time without telling us
useful information.
Set RUN_CURSED_TESTS=1 to run locally.
This change just alters the semantics of the one flaky test, without
trying to speed up timeouts on the others. Empirically, speeding up
the timeouts causes _more_ flakes right now :(
The remaining flake occurs due to a mysterious packet loss. This
doesn't affect normal tailscaled operations, so until I track down
where the loss occurs and fix it, the flaky test is going to be
lenient about packet loss (but not about whether the spray logic
worked).
Signed-off-by: David Anderson <danderson@tailscale.com>
It previously passed incorrectly due to bugs. With those fixed,
it becomes flaky for 2 reasons. One of them is the wireguard handshake
race, which can eat the 1st sprayed packet and prevent roamAddr
discovery. This change fixes that failure, by spreading the test
traffic out enough that additional spraying occurs.
Signed-Off-By: David Anderson <danderson@tailscale.com>
The previous code would skip the DERP short-circuit if roamAddr
was set, which is not what we wanted. More generally, hitting
any of the fast path conditions is a direct return, so we can
just have 3 standalone branches rather than 'else if' stuff.
Signed-Off-By: David Anderson <danderson@tailscale.com>
The effect is subtle: when we're not spraying packets, and have not yet
figured out a curAddr, and we're not spraying, we end up sending to
whatever the first IP is in the iteration order. In English, that
means "when we have no idea where to send packets, and we've given
up on sending to everyone, just send to the first addr we see in
the list."
This is, in general, what we want, because the addrs are in sorted
preference order, low to high, and DERP is the least preferred
destination. So, when we have no idea where to send, send to DERP,
right?
... Except for very historical reasons, appendDests iterated through
addresses in _reverse_ order, most preferred to least preferred.
crawshaw@ believes this was part of the earliest handshaking
algorithm magicsock had, where it slowly iterated through possible
destinations and poked handshakes to them one at a time.
Anyway, because of this historical reverse iteration, in the case
described above of "we have no idea where to send", the code would
end up sending to the _most_ preferred candidate address, rather
than the _least_ preferred. So when in doubt, we'd end up firing
packets into the blackhole of some LAN address that doesn't work,
and connectivity would not work.
This case only comes up if all your non-DERP connectivity options
have failed, so we more or less failed to detect it because we
didn't have a pathological test box deployed. Worse, codependent
bug 2839854994 made DERP accidentally
work sometimes anyway by incorrectly exploiting roamAddr behavior,
albeit at the cost of making DERP traffic symmetric. In fixing
DERP to once again be asymmetric, we effectively removed the
bandaid that was concealing this bug.
Signed-Off-By: David Anderson <danderson@tailscale.com>
DERP traffic is asymmetric by design, with nodes always sending
to their peer's home DERP server. However, if roamAddr is set,
magicsock will always push data there, rather than let DERP
server selection do its thing, so we end up accidentally
creating a symmetric flow.
Signed-Off-By: David Anderson <danderson@tailscale.com>
I started to write a full DNS caching resolver and I realized it was
overkill and wouldn't work on Windows even in Go 1.14 yet, so I'm
doing this tiny one instead for now, just for all our netcheck STUN
derp lookups, and connections to DERP servers. (This will be caching a
exactly 8 DNS entries, all ours.)
Fixes#145 (can be better later, of course)
The value predates the introduction of AddrSet which replaces
the index by tracking curAddr directly.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
This avoids a non-obvious data race, where the JSON decoder ends
up creating do-nothing writes into global variables.
==================
WARNING: DATA RACE
Write at 0x0000011e1860 by goroutine 201:
tailscale.com/wgengine/packet.(*IP).UnmarshalJSON()
/home/crawshaw/repo/corp/oss/wgengine/packet/packet.go:83 +0x2d9
encoding/json.(*decodeState).literalStore()
/home/crawshaw/go/go/src/encoding/json/decode.go:877 +0x445e
...
encoding/json.Unmarshal()
/home/crawshaw/go/go/src/encoding/json/decode.go:107 +0x1de
tailscale.com/control/controlclient.(*Direct).decodeMsg()
/home/crawshaw/repo/corp/oss/control/controlclient/direct.go:615 +0x1ab
tailscale.com/control/controlclient.(*Direct).PollNetMap()
/home/crawshaw/repo/corp/oss/control/controlclient/direct.go:525 +0x1053
tailscale.com/control/controlclient.(*Client).mapRoutine()
/home/crawshaw/repo/corp/oss/control/controlclient/auto.go:428 +0x3a6
Previous read at 0x0000011e1860 by goroutine 86:
tailscale.com/wgengine/filter.matchIPWithoutPorts()
/home/crawshaw/repo/corp/oss/wgengine/filter/match.go:108 +0x91
tailscale.com/wgengine/filter.(*Filter).runIn()
/home/crawshaw/repo/corp/oss/wgengine/filter/filter.go:147 +0x3c6
tailscale.com/wgengine/filter.(*Filter).RunIn()
/home/crawshaw/repo/corp/oss/wgengine/filter/filter.go:127 +0xb0
tailscale.com/wgengine.(*userspaceEngine).SetFilter.func1()
/home/crawshaw/repo/corp/oss/wgengine/userspace.go:390 +0xfc
github.com/tailscale/wireguard-go/device.(*Device).RoutineDecryption()
/home/crawshaw/repo/corp/wireguard-go/device/receive.go:295 +0xa1f
For #112
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
Because wgLock is held while some wireguard-go methods run,
trying to hold wgLock during HandshakeDone potentially creates
lock cycles between wgengine and internals of wireguard-go.
Arguably wireguard-go should call HandshakeDone in a new goroutine,
but until its API promises that, don't make any assumptions here.
Maybe for #110.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
For 3 seconds after a successful handshake, wgengine will send a
ping packet every 300ms to its peer. This ensures the spray logic
in magicsock has something to spray.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
In particular, this is designed to catch the case where a
HandshakeInitiation packet is sent out but the intermediate NATs
have not been primed, so the packet passes over DERP.
In that case, the HandshakeResponse also comes back over DERP,
and the connection proceeds via DERP without ever trying to punch
through the NAT.
With this change, the HandshakeResponse (which was sprayed out
and so primed one NAT) triggers an UpdateDst, which triggers
the extra spray logic.
(For this to work, there has to be an initial supply of packets
to send on to a peer for the three seconds following a handshake.
The source of these packets is left as a future exercise.)
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
This is the first, and easier, part of incremental wireguard-go
reconfiguration. It means that a new node appearing on the
network does not cause all existing nodes to re-handshake with
the other nodes they are talking to.
(This code has been running on hello.ipn.dev for a few weeks and
peers have successfully reconnected to it through many network
map updates.)
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
And make the monitor package portable with no-op implementations on
unsupported operating systems.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
* make RouterGen return an error, not take both tunname and tundev
* also remove RouteGen taking a wireguard/device.Device; currently unused
* remove derp parameter (it'll work differently)
* unexport NewUserspaceRouter in per-OS impls, add documented wrapper
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The MTU is currently set when creating the tun device,
elsewhere in the code. Maybe someday we'll want some kind
of per-platform MTU configuration here, but not in the
short-medium term.
Signed-off-by: David Anderson <dave@natulte.net>
